7MKGDS400DW0 Kenmore Dryer - Instructions

they sent the wrong part . when i got the right part i removed the two screws holding the element . took the Thermostat out . removed the plugs . put the new thermostat in plug in the plugs. screwed the element back in place . And now i need to replace the fuse located at the top of the element casing.

Before ordering the part, I found this website by linking from a video on YouTube where several people showed how they did it. Simply two screws in the lint removel chute and pushed in the two clips holding the top and two inside screws holding the front panel. Held the machine tilted back onto a table and placed two 4" wooden cubes underneath it so it wouldn't come forward and one more 4" cube under the drum. After cleaning out the inside, I slipped the new belt around the drum (ribbed side down) and taped it in place with a couple of pieces of painter's tape temporarily. Hooked the idler wheel guide and looped the belt in it. Tested movement by spinning it by hand to check alignment and removed tape. Reassembled the front, side and top panels accordingly and tested it. Voila! This was my first attempt and I saved myself some bucks. The last repair was done by Se•rs and their service person took my credit card number for the invoice and promptly went out and charged over $3,000 on it. He was eventually caught. Great incentive to do yourself, huh?

The dryer was igniting when initially starting load, but didn't light again the rest of the cycle. On my model the access was through the front panel, didn't even have to pull dryer out. Open the door and there are two screws on each side.of the inside of frame. Remove screws and lift door off the the whole front of the pulls out and down and removes, and everything is right there to work on. Replaced thermostat, that took 5 min. But didn't fix the problem. So I purchased and replaced the "M" Series New Style Coil Kit, took about 10 min. I took olm/continuity readings b/t all terminals of the old and new coils and they were only about 5% difference, the old being a little lower. But that fixed the problem, works like new again.

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

I removed the lint trap then the dryer cover from top and front side. I placed the belt around the dryer drum being sure to put it on the correct side with the grid side against drum. I coiled the belt around the pulley and motor tract. Replaced everything in opposite order in which it was removed.
Video from website was very informative and helpful. I was able to follow along step-by-step to replace the dryer drum belt. I am officially a do-it-your-selfer!!!

It was easy to remove the lint trap first, then the front dryer panel. The drum easily was removed and installing the new belt was a little tricky because the belt had to be mounted onto pulley while holding the drum in place. I had a little help from a friend to help me stabilize the drum as I placed the new belt. Once on, it was easy to re-install parts in reverse and have dryer working again.

My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports

Once I realized it was just a drum belt and how easy it was to fix, I ordered the belt myself with no help from a national warehouse hardware chain where the manager said "I don't have a belt but I can sell you a dryer." Thank you I kept my 300+ dollars and once I got the belt it only required removing the two screws that sealed the lint screen cannel to the top; popping the top, removing the to nutbolts fastening the front to the side panels; slidding the front panel out; putting the belt around the drum and attaching it properly to the tension pully and motor. Finally, I closed it up and tested it. Household hero in less than 12 minutes! Not bad for a psychologist, eh?

first I took the two screws that hold the filter in, then disconected the power,then I poped the top of dryer up and removed the two 5/16 screws on the inside of the front panel then the two screws down by the loading door hinges and took off the front cover and the drum, replaced the belt and put the ajuster back on and put everything back in revers order and it is working like new thank you for the fast order .tony

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

Took two screws out of the Lint tray on top. remove to bolts from under hood then put new belt on. Always make sure there are no twists in belt when put back on

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

still no heat.

First unplug the machine and turn off the gas. Then, I pried the top up (2 clamps on front, 2 screws to the lint screen). Then I removed 2 5/16 nuts that fastened front panel to sides. I held the drum and pried the front panel back while my wife slipped the new belt around the drum. Then, I buttoned everything back up in reverse order, removed the kick panel, threaded the belt through the tensioner pulley and around the motor shaft. It's really that easy. PartSelect.com makes it simple with quick, accurate service.