1103402851 Kenmore Dryer - Instructions

Downloaded a schematic of the dryer controls. Watched a UTUBE video of how to remove the front panel of a Maytag Performa dryer. It was pretty easy. Consulted your website and found out that bad coils are typical of the symptoms 46% of the time. I have bought parts from you before and happy with results.

the repair was an easy fix, I removed the two screws from the brackets holding the coils, disconnect and removed them installed the new coils connected plugs turned on dryer and I got heat not bad at all thank you for the help

Initially confused by instructions provided in that it stated to loosen a brass coupler. Disconnected power. Removed front bottom panel. Disconnected both leads to ingiter. Removed the 2 screws holding igniter bracket in place. Carefully slid igniter and bracket forward and removed from dryer. Removed screw holding ingiter and replaced with new. Reinstalled in reverse.

I first replaced the temperature sensor. That did not help and when doing investigation when thr drier was warm I found the vallve would open and close if I touched the coils

First I stumbled around on my own trying to figure out the problem then I remembered PartSelect & the info I got to fix the dishwasher. The info given for the dryer pointed to 2 main problems for no heat, tested them with the Ohm meter & ordered the part. We have a dryer again !!

Repair was easy, remove bottom cover, remove screws that hold coil bracket, remove old coils & slip new ones on & button up. Dryer works fine now.Had the new parts within 3 days. Thanks PartSelect!

Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.

The hard part of the repair was the diagnosis. I'd take the front off the dryer, start it up, and the flame would fire up. I'd put it all together, start it, hear the flame start, leave, and it would still be running 4 hours later with the clothes wet. Discovered that one of the gas valve coils would work cool and show connectivity, but would stop working shortly after starting. To check the flame and remove the front, remove the door - 1 phillips screw in each hinge, then jiggle up and down pulling away from the dryer. Then, two screws on the opposite side. Facing the opening, grasp front and pull toward you to swing it down. You can temporarily put the door back with the front off while you start it to watch the flame cycle. On regular heat, the flame will run pretty much continuously - in my case, it would start, run for about 1 minute then stop. I assumed it was cycling, but it really runs longer than that. Coil replacement was easy - unplug the dryer, pry off the electrical connectors, remove the two screws on the left which hold the retainer containing the coils Then pull the coils straight up and replace with new ones. The one with three connectors is in front; the one with two connectors in the back. There are plastic tabs on the coils which fit into holes on the retainer. Reassemble in reverse order. To confirm diagnosis, you can use an ohmmeter to check continuity of the coils. The front coil has continuity between the center connector and each of the side connectors. The back coil has continuity between the two connectors. If you're not getting a reading at 1k ohms, it's probably an open coil and needs replacement.

Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.

Since the power and gas to the dryer were both already turned off all I had to was open the top of the dryer, remove the front panel, look underneath the drying drum and remove the belt tensioner from the belt and slide the drying drum out. While things were open I took my vacuum and vacuumed all the lint, dirt and loose articles from over time out of the dryer interior. I located the igniter, used a nut driver to remove one screw pulled the igniter from its housing and disconnected the wiring harness. For installation I reversed the process and I was done. I reinstalled the drying drum, reattached the belt tensioner, put the front panel back in place and closed the dryer top. Attached the dryer vent hose, plugged the dryer to the electrical outlet, turned on the gas and walla it purred like a kitten. It even seem to dry faster than before.

Checked the resistor to confirm it was good. Removed the two screws that are accessible after you pull the lint screen out. Use puddy knife to release the two plastic clips that hold the top on. The top will pop up like car hood. You have to pull up on it with steady pressure. I used a plastic puddy knife to prevent scratching anything. Prop top up so it does not fall back down and strike your head or fingers. On each side inside the housing there is a sheet metal screw that holds the front of the dryer on. Before you remove them unplug the door switch wire. As you get these off you will notice that the whole front is loose and the drum looks like it will fall out. It may if you mess with it. Gently tip the front away from the dryer housing and drum assembly. After the front is out about 5 inches pull up and the bottom can be moved away out of the small hook clips. Set it aside. The burner assembly is on the lower left. The coils are there remove the sheet metal screws and lift it up. Remove them one at a time. Notice the small locate pin and position the coil in the same orientation assemble in reverse. The door is tricky to get back on. Don't forget to unplug before doing any work. This can be done without disconnecting the gas service.

Unplug electric, open top, take off front, with a small Phillips screw driver remove two screws securing the coils, remove one coil at a time, unplug and replace with new coil, secure with metal bracket and reinstall front and top and your done.

The dual cil gas valves were out of resistance range. The new coils were easy to install with a screw driver, sockets set and multi-meter.I checked the coil resistance and one of the new coils were a little high, but I installed them and they have been working fine.

I went onto the Part Select website, they have a problem solving section that told me the most likely part to replace first and a description of the machine and the location of the part. I purchased the part, I unplugged the electric cord first. I then opened up the front of the machine with a philips screw driver, changed the part with the philips scew driver, I put back the front of the machine and the machine worked. It doesn't get any better then that!

Pulled out AC cord from wall socket first! Removed the dryer door and front panel (2 screws each) Then pulled both wire connectors off 2 coils. Removed hold -down bracket over coils. Replaced both coils and reconnect . No need to replace electronic igniter for gas. The right parts were shipped faster than I expected. Easy job. The Maytag repairman remained unemployed once again!