110C60122510 Kenmore Dryer - Instructions

I removed the top panel, then the front panel.
Removed the belt and the drum.
Saw what I needed to replace. Ordered the parts then put back together. It was a really easy job.

Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.

Dryer didn't heat. I got the heating element thru sears and when I ordered it I thought I should also order the thermostats but I didn't. Element arrived two days after ordered right on time. Slipped right in in a few minutes. Turned dryer on. No heat. Went back to drawing board. Watched videos on part select site and realized I needed thermostats. Ordered them and lint filter. Arrived right on schedule and also slipped in in no time flat. Turned dryer on and yes it heated perfectly. Wife was pretty impressed with new lint filter as other one was torn with jagged edges. MY SUGGESTION: if your dryer doesn't heat and you can't test each individual item thermostats and heating element order the three of them ( high limit and cycling thermostats and heating element) cause they'll probably will all go at the same time anyway. Then won't have to wait on the second shipment if things don't work with partial replacement. Parts select was great and videos are well understood and easy to follow. Would certainly use again.

Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

First, let me say the t videos are excellent. Check them out if you haven't already.

I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.

I took a chance and ordered the maintenance kit to avoid having to take the dryer part to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .

Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.

Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.

As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.

It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.

One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)

It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.

Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.

Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new

Followed the video .... Also installed another part. which was a kit. the video here showed the third wire being installed. The video on repair clinic did not show where to attach the third wire (orange wire). The Kit and the Thermostat was installed with 25 mins. Thanks

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

Replaced power cord, terminal block, and all melted wiring. Checked the thermal fuse for zero resistance.

I knew that the dryer needed a new belt and since the dryer was also failing to dry the clothes in one cycle, I decided to replace the three thermostats, figuring that I might as well do all three if I'm going to open up the dryer. I downloaded a schematic of the dryer from the Whirlpool web site, which helped me to order the right parts and see how I would be able to make the repairs. Once I figured out how to get to the drum for the belt replacement, installation was quite easy.

First step was to unplug the dryer, remove the vent hose and remove the back panel with a nut driver. Once the back panel was removed, it was easy to see all three sensors. The heating element unit was easy to remove - two screws. This made it easier to replace the sensor. Each sensor was shaped differently, making it easier to decide what went where. This normally would not have been a problem, but the part numbers have changed for this dryer. I could have also cross referenced the parts by using the partselect.com web site.

To access the dryer drum, I had to remove two screws on the back of the dryer that are located in two tabs that hold the control panel to the dryer cabinet. Once removed, it was easy to lift the top of the cabinet and swing it up and against a nearby wall for support while I replaced the belt.
I removed the old belt from the motor pulley, and then just removed the whole drum. I placed the new belt around the drum, placed the drum back in position. With my wife supporting the drum, it was easy to bring the belt through a guide and slip over the motor pulley. Then, I rotated the drum manually to make sure the belt wasn't twisted.

After ten minutes of putting everything back together, it was time to plug in the dryer and test it. I did it without a load first and checked the vent for hot air. After that, we did a couple of loads...one on high and one on perma press, and when the cycle was over, the clothes were dry!

Delivery time from PartSelect was super fast! Prices are excellent, and I really appreciate such a helpful web site. Anyone with a small amount of mechanical ability and "do it yourself" experience can save $$$ by fixing it yourself. Having someone service this dryer would have cost me more just to replace the belt.....let alone the added insurance of replacing the sensors. And, I learned that if the heating element should fail, replacing it would be a snap, and would start with a visit toe partselect.com!

I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting

I ordered the belt idler pully and drum support rollers and after watching the video on Parts Select web page, changed the parts. It could be done by one person, however having a second person to help with the drum installation worked great. I discovered the motor bearing on the front side of the motor was the source of the squeek. I disassembled the dryer again and removed the motor. After ordering a motor the installation and reassembly went smoothly. The parts came in two days of placing the orders and virtually new parts in the dryer makes it seem like a new machine.

First I pulled the dryer away from the wall and unplugged it. Next I removed the dryer vent hose and threw it away and replaced it with a more rigid metal vent hose. Next, I used a socket wrench to removed the screws holding on the back cover of the dryer. Once the back cover was off it was just a matter of using the socket wrench to removed the bolt holding the sensor in place. After the part was removed I made sure the replacement was orientated in the same way as the original part and then I unplugged the wires from the bad sensor and placed them in the same order on the new part and then I bolted the new sensor back in place. Since the new part has been installed the dryer is working flawlessly and is not turning off mid-cycle like it was. ***Oh, and an important reminder. When you have the back cover pulled off the dryer use a shop vacuum to suck out any dirt and lint in the back of the dryer and make sure you unbolt the metal chute that the dryer lint screen goes into and clean inside the area near the exhaust blower. This is a VERY IMPORTANT part of servicing your dryer and should be done every few months to help avoid the risk of a fire.****