110C68132413 Kenmore Dryer - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.

UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use small screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new washer and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

My husband changed the idler pulley. It took him 5 min. Thank you sooooooooooo much. Saved us 1000.00 dollars. He wanted to by a new one but investigated the problem on line. He is a handyman and was just being lazy. I ordered the part and he fixed it. I love saving money!!!!!!!!!!!!! And I love my husband!!!!!!!!!!!!!!

I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.

Simply slid new idler wheel on then popped thr tri ring on. The belt replacment was the hardest thing which was also easy. I think pulling the dryer away from the wall was the most difficult thing.

Used a ropeasround the dyer drum to simulate thebelt to peload the idler This allowed me to get the belt over the motor shaft without the idler sping tenion causing the idler to jump at random timesafer I strted using the rope the belt was on in 10 minutes.

Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.

Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.

Watching the video from Parts Select for replacing the rollers showed us all we needed to easily replace the wheels as well as the Pulley and belt. It made a gigantic different in the noise and efficiency of the dryer. One of the Wheels was actually 3/4 gone, worn away. Hopefully, this repair will extend the life of an already old dryer. Thanks for the videos that made the repair a 'piece of cake'.

it was easy all the parts were the exact replacement

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.