Models > 11068133414 > Instructions

11068133414 Kenmore Dryer - Instructions

Jump to:

All Instructions for the 11068133414
91 - 105 of 159
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mahen from Shattuck, OK
Parts Used:
WP3387747
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Dryer not heating
Removed the front bottom panel. Disconnect the two wires and two screws and then remove the heater element using pliers. Then install the new heater element in the same way.It works good as new now! Thanks to PartSelect.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joel from Richfield, PA
Parts Used:
WP3387747
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
No Heat
Took bottom accesses panel off dryer (two screws). To the right was heating element housing. Three screws to remove inside. One at the bottom of houseing bracket (holds up heating element housing) which connects to dryer cabinet floor. One at top of bracket (connects to bottom of heating element housing). One on the left side where the elements wires connect (screw goes through housing then through element side arm). Once the three screws are removed disconnect wires and pull element stright towards you. Once everything was diasembled I took shopvac in side machine and swept it all out. Just reassble the same way you took apart.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carol from Apopka, FL
Parts Used:
WP3387747
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Dryer wouldnt heat up
Removed toe plate, make sure and use something like a 5 in 1 painters tool, makes the job easier as you will see a notch inside the seam between toe plate and outer shell, take 1 screw from heater tube cover I used a nut driver, this job is best to use with a stubby socket set, there are 2 machine screws with hex heads holding the heating element to the heating tube, you cant really see the heads but can feel them with your fingers, disconnect the 2 terminals in front of this, but make sure you use a blue or black sharpie to mark the terminals, use your stubby and remove screws, then use a set of needle nose pliers and pull out the heating element, the new heating element slide right in the grooves then reverse the take off process, good luck
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ben from West Harrison, IN
Parts Used:
WP3387747
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
No Heat
I watched your online repair video, which was excellent. As I started the repair, it was exactly as described in the video....very easy. The only thing I did differently was clean out the mechanical compartment of the dryer with a shop vac.....simply because it was full of lint. There is nothing I won't try to fix; but this job can be done by anyone. Do it yourself; don't spend the money to have someone else do it.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nathan from Saint Marys, GA
Parts Used:
WP3387747
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer would tumble but would not get hot.
Being from the old school where we never assume to know what the problem was, so took out the heating element to inspect which I found that the element had a broken coil which confermed my suspicions. I ordered a new element on Saturday from paRts select on Saturday and recieved it on Wednesday Ann the rest was a matter of reassembling which was a breeze since I foot plenty of pictures.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phil from Apex, NC
Parts Used:
WP3387747
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Dryer would not heat
Remove two screws holding front panel of dryer. Heating element is on right side, in a protective tube. Remove the six wires connected to the tube, noting their placement. Remove two screws from front metal bracket holding in the tube. Pull tube out. One screw is holding the heating element in the tube, so remove that and you can replace the element. Then reverse to put it all back together. Clean out all of the lint inside the dryer.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Melody from White Bluff, TN
Parts Used:
WP3387747
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Eement was burned in to.
It was very easy to repair and the 1-800 number is a grat resource for assistnat in locating the part.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dr J Randy from Stone Mountain, GA
Parts Used:
WP3387747
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set, Wrench (Adjustable)
No Heat
Followed the instructions from the Whirlpool Technical Service Manual available online
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Margaret from Woodbine, GA
Parts Used:
WP3387747
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
dryer stopped heating
First, we unclogged the blocked duct (which, is apparently what burned up the heating unit in the first place!), then, we took off the front of the dryer panel; then we loosened up the heating unit's case and took out the existing heating unit. It was apparent why it wasn't working. You'll have to see yours for yourself. Then, we installed the new unit, put the heat shield back on, closed up the dryer and turned it on. No heat... oops because we forgot to put the electricity to the unit... so we took the panel back off, then plugged the wires up to the heating unit, as we should have the first time, closed up the panel, and voila! The dryer was working again, and for a major fraction of the cost of replacing the thing! 45 dollars instead of 800. Well worth the time! And the 14 year old did the repair. Explains the first plug in mishap, but also taught him a good skill!!!
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Malvern, PA
Parts Used:
WP3387747
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
the dryer was turning and getting no heat
first turn off the power supply then ..removed the lower front cover. .removed the heat shield that covers the element. .. removed the element and replaced with the new one ..
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Todd from Austin, TX
Parts Used:
WP3387747
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
no heat in dryer
I opened up the bottom of the cabinet and found some evidence of burned lint in the heater box. I ohmed out the thermostats and they were good. Then I ohmed out the heater coil and found that it was an open circuit.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brad from Wausau, WI
Parts Used:
WP8577274
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Gas dryer shut off mid cycle in timed cycle mode
Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.
3 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from Williamsburg, NM
Parts Used:
WP3387747
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Heating element on my dryer had stopped working
Disconnected dryer from power source. Removed bottom panel on dryer. Removed three screws. Disconnected two wires on heating element. Pulled heating element out. Attached new heating element. Success!
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jose from Russellville, AL
Parts Used:
WP3387747
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
Would turn on but not dry.
Opened the bottom section removed the heater element replaced it and boom!! It works!!!!!
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles W from Roanoke Rapids, NC
Parts Used:
WP3387747
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Dryer stopped heating
I ordered the Part on Wednesday night, it arrived on Saturday, and was installed by Monday by my husband. This was the best service I have seen in a good while. Kudos to you!
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11068133414
91 - 105 of 159