1106407902 Kenmore Dryer - Instructions

Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!

Pop out the old latch and replaced with a new one

Simply installed the piece and I was done. Took 10 seconds.

Removed old catch and strike with screwdriver and needle nose pliers. Installed new parts. My old catch did not have comparible numbers so I just used the yellow one. Worked fine.

All I had to do was get the model number off of the dryer and plug that information in online and within a couple of days the part arrived. It was great! There were directions that came with the part that explained how to replace the old latch with the new one.

I remember in the "olden days" when I would of had to call a repair guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.

Awesome!

Popped out the old door catch kit and replaced it with the new one! Easy!!

First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on and reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.

Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

We got the part so fast we were both surprised. My husband installed the part by just seeing how the old one came off. It was simple and fairly quick. Except that his hands are so big they had a hard time fitting in to where the part needed to go. Just opened the top of the dryer, took the old part out and put the new one in.

Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.

The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.