11062182103 Kenmore Dryer - Instructions

So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.

I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.

Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.

The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)

Can't beat parts select!

Parts select + a little know how, saved me about $400.

Never did get the part. Initial order was not the right part. Ordered the right part on 12.2 and this is 12.18. While the initial oder and delivery was correct, they do not tell you that you do not have to ship by Fed ex. Fed Ex seems to not be able to provide service to our address despite driving past it several times a day.

this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!

Checked on your website for common problems w/this model dryer,highest probability was the thermal fuse being blown,so I ordered one & checked the vent for being plugged,no problem there,removed the back of the dryer replaced the fuse(very easy to do)put everything back together & started it up...all set now.Thanks for your help

I watched the video several times before beginning, which was very helpful. As I didn't have the tool that was recommended in the video, I used pliers, which although took longer, worked out fine. I also used pliers to pull the wires off of the old thermal fuse. My dryer had been not working for 2 months, so I was very pleased that I was able to watch a very detailed video, order the parts on the same website, and receive them very quickly (within couple of days.) My daughter who lives in another state googled my dryer model number with a description of the problem and found your website. She sent me the link of the video to watch as it appeared very easy to understand. She and I both were very impressed by the step-by-step instructions on the video, including a list of all the tools required. I am an 81 year old woman and had no problems fixing this by myself with the assistance of your website. I have recommended this site to several of many friends and family members. Thank you!

There was no heat but the dryer would operate properly in all other functions. I checked the ignitor (gas dryer) with a meter and it was okay. I traced the circut back and ended up at the thermal fuse and it was "open" I jumped it out and the dryer started to work. I knew the problem was the thermal fuse but more importantly why did it blow. Further investigation showed excessive lint in the duct. Needed to take the exhaust system apart and clean out the lint. also replaced the flexible dryer (too difficult to clean) and to make sure that I didn't over work the high/low thermostat and would be doing this repair again in the near future I replaced that also. Be careful and do not jump out the fuse and use the dryer as this will cause a fire. I did it to prove the problem only... Dryer works well again and we will probably get another 5 years out of it!

Al
hrguy@comcast.net

NOTE: Please make sure the dryer is un-plugged any time you are reaching into the access panel with your hands or a tool. There are exposed connections everywhere. After using the diagnostic testing instructions (usually attached to the inside of the front panel) I determined it was a faulty Thermal Fuse. The PartSelect video instructs you to take half the dryer apart to access the Thermal Fuse, but I found it easy enough to just access it with the front panel removed. I used a small 1/4" drive socket to remove the single hex head sheet metal screw holding the Thermal Fuse in place. I then slid the 2 wires off, noting which went to which lug. Installed the new thermal fuse and after starting the screw by hand, tightening with the small socket wrench. It is a bit tricky to reconnect the wires as you are doing it all by feel, but it's a lot easier than taking half the dryer apart. Also, make sure you check the exhaust path for obstructions, that might be why the ThermalFuse blew in the first place.

Longest time needed was to determine what cause was. After that ordering part from PartSelect was very easy and saved me money. Part arrived before time given, part was correct and installed without problems.

My wife and I thought our dryer was done and we were looking at a large replacement costs. We started googling and found this site and watched the video. We are were 99% sure it was the thermal fuse. We received within 2 days and thought we would be in there for over an hour. Turned it was less than 10 minutes, we watched the video clip on how to install on our laptop as we did it.

We will always be buying parts from this site and have told a ton of friends/family to check this site out.

It saved us so much money!!!!

I followed your short video and found it very easy to do

Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.

The Termal Fuse did not solve the problem. Ordered a heating element so I hope its that

took off back, took out 1 screw of thermal fuse. pulled off 2 wires. put on new thermal fuse put back 1 screw and plugged. in both wires. plugged in dryer to make sure it worked. threw in some wet clothes to make sure it worked.

Looked it up on YouTube. It told me to take the front panel off. I did, changed the belt, put the panel back on and it works perfectly. The part came in the time it was supposed to and it was the correct part. Thanks.

Found multiple videos on how to diagnose the problem. Parts plus showed me that over 50% of the time the problem was the thermal fuse. I put a jumper wire between the two connections on the thermal fuse to see if the dryer would fire up. Sure enough it did. Bought the $10 thermal fuse and changed it in less than 15 min.