1106957700 Kenmore Dryer - Instructions

After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and although not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.

I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business

just replaced parys

Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.

just followed the video directions, worked perfectly thanks

removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!

Followed Youtube video - quick & easy

Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.

I followed your short video and found it very easy to do

Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allow top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.

Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.