11079495610 Kenmore Dryer - Instructions

Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

Disassembled dryer, removed tumbler, replaced drum support rollers

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business

just replaced parys

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

Replaced lid switch, but problem still continued.