999L30XG Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Royal Palm Beach, FL
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Clothes were not getting dry enought
Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David M from Watertown, WI
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would heat up for a short time, then shut off
First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Spring Lake, MI
- Parts Used:
- 12001348
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dryer would not heat. Gas valve came on then went out in less than 4 seconds
After unsuccessful results with Radiant flame sensor and ignition coil kit replacement, jumpered high temperature sensor and flame remained lit. Replaced sensor and all is well. Very pleased with Parts Select delivery and user problem solving section on web site. Clothes Dryer back in service before the next weekly laundry day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Garden City, NY
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer worked but did not heat
Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Whitehall, MI
- Parts Used:
- WP305605
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
No heat burner wouldn't ignite
Removed front panel, bypassed door switch to allow dryer to cycle on. In the regular setting the igniter cycled OK but, no gas flow. I disconnected and sepperated the three solinoid coils (be sure to mark them the wires have to be exactly as they came apart) then, tested each coil with an ohm meter. The booster coil was open causing the problem. Replaced the booster coil dryer works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Quinn from Los Alamos, NM
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Dryer would stat but no heat
The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ambler, PA
- Parts Used:
- WP338906
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer will not get hot
Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.
Was this instruction helpful to you?
Thank you for voting!