1106099299 Kenmore Dryer - Instructions

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pulley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

Turned off my circuit breaker first. Removed back panel with a 1/4 nut driver. Replaced the dryer fuse first. Very easy but did not fix the problem. Watched how to videos to narrow down the parts I might need. Purchased the thermal cut off kit. Installed the High limit thermostat first. Tested the dryer, no dice. Finally installed the Thermal cutoff. BAM!! I have heat. Since this is an older dryer I did need to use some WD40 to loosen some of the connections. Total cost of parts including tax and quick delivery was $48.30. Fantastic. My old man told me it was unfixable. He was wrong. I WIN. This site is a great teaching site. Thank you!

Two screws hold the top control panel in place. Once removed the panel could be tipped forward. The Push to Start switch had 2 wires which were removed and swapped to the new starter switch. The old one rotated 90 degrees to remove and the new one installed. Panel was resecured to the top of the dryer and tested. Worked first time. Finding the part on the website, ordering it, receiving it quickly and the install couldn't have been easier or more pleasant or efficient.

i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal Fuse blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Removed the dryer door, unscrewed lint vent.