MDE336REW0 Kelvinator Dryer - Instructions

Remove rear control panel cover and remove drum belt from pulleys. remove top cover by pushing in on the 2 hold down fasteners on the front with flat head srewdriver. remove front panel by removing the 2 screws and then pop it out by lifting up. disconnect the wires at the quick connect plugs and set the front aside. lift the drum up to pop it out of the bearing housing and move forward slightly to give youself good access to the wires for the heating element and disconnect the 2 wires. remove drum the reset of the way out and do your work. Replacing the heating pan and drum bearing is pretty obvious what to do. (just a few screws). remove thermal cutoff switch from old pan and install on new pan. reinstall in reverse. no need to label wires because it doesn't matter where the wires go an a switch (justs makes and breaks a circuit) and the heater doesn't matter as long as both wires are hooked up to complete the circuit. You can't mess up the quick connectors on the door. Only my heater failed but I also replaced the drum bearing as long as I had it all apart (only another ~$20). Take the time to clean out the dust from inside the dryer, it will help the blower motor run cleaner and cooler and last longer. I bought a belt also to have on hand for replacement. I didn't replace it since my old one was good and it is real quick to replace at a later time.

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

Ordered in new Element. (took apart dryer first and verified the coil on the old element was broken).

-Disconnected power
-Used flat blade screw driver and popped the top of the dryer off (two clips at front of the dryer on the door piece). Pull lid back and it will rest on its own.
-Removed two screws on the inside of the front door panel then used flat blade to pop four clips off. Lift up then out to removed door panel, drum will fall down.
-Removed small white plastic rest from front frame.
-Removed back silver vent to access motor. Pull the belt tensor away from assembly and pull belt out.
-Remove drum by grabbing belt and front of drum and forcing it up until it releases from the ball housing. Slide drum out of the front of frame/dryer.
-From here you can see the heating element. disconnect the coil wires (pull them). These are in series so it doesn't matter how they go back on. Disconnect the thermostat wires (X is negative lead).
-Removed the four screws from the back of the dryer to disengaged the element. Removed.
-Reassemble backwards.

First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect.
Mike

Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)

replaced bearing and shaft new belt and everything works just fine

Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.

Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhesive to glue on the new guide. Use masking tape to hold it while it dried.

Reverse the first paragraph to re-install.

I followed the instillation instructions provided on your website. They were very informative and spot on. My only problem was my strength. I could not get the drum off of the rear bearing myself, but then I am a 61 year old female.

I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado

Had to open back side vent & use needle nose to secure spring.

Unplugged the dryer, removed the top of, disconnected the electrical connectors, removed the front panel, disconnected the belt, removed the drum, removed the old Safety Thermostat, installed the new Safety Thermostat and assembled the dryer again.

The repair went smoothly considering I am a rookie. The repair videos on your site are great. Followed the techs instructions and got thru it fine.

Thanks,

Jim

This was a simple repair. Before I ordered the parts I had read several of the "repair stories" on this site, plus my neighbor explained to me the process. So I had a good idea of what I was getting into.

I am not real sure how long it took because I was watching a football game while I was making the repair, but I would guess if I did it straight through it would be about 1 hr.

Replacing the Drum Glide and Lower Basket Seal
1) Pulled dryer out from the wall
2) Unplugged Dryer
3) Pop the top off the dryer. Insert a screw driver in the crack right at the corners to pry
the top off.
4) My dryer had a quick connector for all the wiring (which I found half way through the
repair) that allowed me to disconnect all the wires leading to the door. If you can find
that disconnect that so you can easily remove the door & front panel.
5) Removed two screws holding the front panel on.
6) Remove the front panel. Once the 2 screws are removed the only thing holding my
front panel on were a couple of clips.
7) Removed the Drum Glide (top) & Lower Basket Seal (bottom) around the door frame in
the front panel. This is the worst part because you have to scrape a lot of the glue
and it takes a little while to do this.
8) Glue the Drum Glide. I used some spring clamps to hold it in place. Glue did come with
the Drum Glide (but not the Lower Basket Seal)
9) Glue the Lower Basket Seal. Since I only had 4 spring clamps I waited until the Drum
Glide was secure. So if you have several of these clamps that would be best.
** if not replacing the belt skip that section.

Replacing Dryer Drum Belt
I took a lot of the people's advise and replaced the belt while I had the dryer apart. But if you are only replacing the belt perform steps 1 - 6 above first.
1) Remove the access panel on the back of the dryer. Mine had for screws.
2) Remove the belt. There is a spring loaded pulley that you just move to one side so the
belt will loosen up enough to remove.
3) Place the new belt on. I started in the front and moved the belt over the drum to the
back. Then moved to the back of the dryer and through the access panel placed the
belt over the pulleys.

Thats pretty much it. I barely got dirty. Oh, while I was in there I cleaned as much lint as I could. That was the dirty part. Now all you have to do is put it back together.
1) Reconnect the front panel, and wire harness.
2) Plug it back in.

If you are wondering why I didn't replace the bearing, I didn't have any grease and the part fit but didn't look exactly like the current one. And the current one looked ok. Since this was my first attempt at fixing a dryer; I decided not to press my luck.