JDG3000W Jenn-Air Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Chicago, IL
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Gas dryer would not heat - pilot lit briefly then went off
Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit
PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit
PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tara from North Canton, OH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Female End Of The Door Catch Broke
First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vernon from chowchilla, CA
- Parts Used:
- WP53-0918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
hole in lint filter
ordered lint filter and it was here the next day.
GREATE SERVICE!!!!
GREATE SERVICE!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Memphis, TN
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The dryer door latch was broken.
The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from Grand Rapids, MI
- Parts Used:
- WP31001344, 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Belt broke
Real easy I have resurrected my dryer may times so this was easy to replace the belt and idler pulley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eli from North Stonongton, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay shut
Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LARAMIE, WY
- Parts Used:
- LA-1003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Broken Catch
Watch the video. Very, very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Livingston, TX
- Parts Used:
- LA-1003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door wasn't staying closed
popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cheryl from international falls, MN
- Parts Used:
- 31001096
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer made a horrible racket when running
my ex husband took the top and front of dryer off and removed the drum and belt. he pulled off the worn roller and replaced it with the new one. we put the drum in backwards and had to turn it around but all went well and the dryer is quiet again!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Schaumburg, IL
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
My drier would start create heat,than stop heating after 8-10minutes.
After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chuck from smithtown, NY
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer heat would go off and timer would not move. Dryer would continuously run
Replaced coils on gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Floyd, VA
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Too much drying time, not hot enough
I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.
Good trouble shooting information.
Good trouble shooting information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from East Tawas, MI
- Parts Used:
- LA-1008, WP53-2287, WP31001470, WP31001469, 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Metal To Metal Contact And Rubbing Noise
Took the front of dryer apart removed belt and drum replaced my parts and reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHUCK from HARDIN, KY
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ignitor failed to ignite gas or would fail to after first ignition.
Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth V from Westminster, CO
- Parts Used:
- WP53-0918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No Problem, Old filter had seen better days.
No Repair, just replacement. Went perfect.
Was this instruction helpful to you?
Thank you for voting!