MHE15MNAGW International Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from Rancho Cordova, CA
- Parts Used:
- WP6-3700340, WP33002535, 12001541
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
squeeking
Pulled the front off. then the inner face and drum. removed belt and two pulleys and re-installed. took me 45 mins. never done it before. watch the video that comes with the parts confirmation you get online and do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Exeter, RI
- Parts Used:
- WP33001755
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer Baffle had broken & needed replacement
Removed door &clips on latch side of door using a philips screw driver. Removed the dryer front panel by hand exposing the two metal clips holding down the dryer top panel. Using a nut driver, the two clips were removed allowing the top panel to be raised. The dryer drum was manually rotated to the location of the broken baffle. Using a nut driver, the broken baffle was removed. The new baffle was installed in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James C. from Cobbs Creek, VA
- Parts Used:
- WP694674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
not enough heat to dry clothes
always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rommel from hercules, CA
- Parts Used:
- WP33001762
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas flame shutting down after a minute.
replaced both solenoids on the gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bend, OR
- Parts Used:
- WP6-3700340, WP6-3129480, WP33002535, 12001541
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Drying had starting making a loud screeching noise
The noise started intermittent and got worse. After watching an online repair of a very similar model and same brand, I decided to tackle it myself. The problem was that one of the drum support rollers had seized up. The shaft that support roller road on was also a little sticky. The noise was caused by the roller hitting the sheet metal behind the drum support roller and scraping on it. I replaced the shaft and drum roller and believe that solved the problem. I ordered other parts for the dryer drum assembly and replaced them while I had it apart. I didn't want to take it apart twice so I didn't take the time to disassemble to diagnose it. I just ordered them all and replaced them all while I was in there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Bedford, TX
- Parts Used:
- 12001541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
It was making a lot of noises
IT was good My husband fixed it .sorry we didn't take video but it is working alright. Thank you
Was this instruction helpful to you?
Thank you for voting!