HTDP120GD4WW Hotpoint Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from MARENGO, OH
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher wouldn’t start
Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dameon from SMYRNA, DE
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dishwasher would not start
Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from LAWRENCEVILLE, GA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer drum wasn't spinning, but I could hear the motor and feel the heat from the heating element.
UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.
The video on the site is easy to understand and a snap to follow.
The video on the site is easy to understand and a snap to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from LAS VEGAS, NV
- Parts Used:
- WE03X25079, WE14X25080, WE09X27634, WE03X37319, WE03X37320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Very noisy operation
Very easy! Removed old parts, and installed new parts in reverse order. Dryer was running, and sounded like a new appliance in 35 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from WESTFIELD, NJ
- Parts Used:
- WE03X31620, WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Noisey squeaking noise.
Replaced the rear drum bearing, Front drum bearing,front bearing tabs and belt. I replaced the belt from the front of dryer. Better to go thru the back. Much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jack from payette, ID
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
had a bad switch,would not start
opened up the control cover, pulled off the 3 wires to the switch. unclipped the swutch from the panel and reinstalled the new exact replacemnt sww you sent
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from KEITHVILLE, LA
- Parts Used:
- WE04X20415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dryer began shutting off before timer had come to the "off" position.
I first removed the the timer knob and the other ones from the front of the control panel. Then I removed the three screws that held the rear access to the control panel. Disconnected all wires to the timer keeping written info to which wires went to which terminal. The replacement timer was exactly like the original in the placement and designation of the terminals. I then twisted the bad timer out of the plastic holders, placed the new one and twisted it in place, and replaced the wires. I then replaced the screws in the rear of the panel and replaced the knobs. It did not take much longer than writing this. Very easy and I am completely satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STAN from UPPER ARLNGTN, OH
- Parts Used:
- WE1M1011
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic housing for the door latch mounted in the chassis of the dryer was damaged so the section of the latch in the door wouldn't align.
This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from THIBODAUX, LA
- Parts Used:
- WH01X10313, WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
timer knob and on/off knobs split at base, not engaging
Popped off old knobs, popped in new. Sorry, nothin' to it or I would'a yelled HELP!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUCILLE from MILLVALE, PA
- Parts Used:
- WE04X20415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The dryer would not shut off
On my 80th Birthday my son and I replaced the timer. We removed the screws from the back panel. Disconnected the dryer from the electrical outlet. Removed the knob from the front panel. Pulled out the timer and took a picture of the wires connected to the timer. Then we transferred each wire one at a time from the old timer to the new timer. Then we replaced the timer and reconnected the knob on the front. Closed the front panel. Replaced the back. Then for the moment of truth: we set the timer for a few minutes and pushed start. A few minutes later the buzzer went off and the dryer stopped. And we both screamed and praised the Lord. We had never done anything like this before
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from ROLESVILLE, NC
- Parts Used:
- WD21X10261
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Claremont, NC
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dyer start knob broke.
Dryer is 3 yeras old. This dryer switch / start knob broke three times. First two GE repair fixed it. Charge was about $75 to $100. Then I found Parts Select, Who what great prices. Switch cost under $10. and took me 10 minutes to install. Dryer works great again. OH, I ordered an extra switch to have on hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerard from goldsboro, NC
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the felt in front door worn out
i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from LAKE CITY, SC
- Parts Used:
- WH01X10313
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob and clip both broken
I just removed old parts And put the new part on it was very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from LILBURN, GA
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Catching clothing and reping
Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new
Was this instruction helpful to you?
Thank you for voting!