DLB2450BSL Hotpoint Dryer - Instructions

This wan't a repair. It was simply a part replacement for a part that was easily accessable. I was more pleased at the fact that I could find the part considering how old the dryer is.

Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1

Easy as steps 1 & 2, remove old filter & replace w/ new.
It fit perfectly which was my main concern, as I could not tell from picture if the length was correct.
I am very pleased w/ product & it works just fine..

I called customer Servioce and they helped me with the corrfect part number

drive belt gone, replaced belt and bearing

unknown
25 year old GE dryer started making strange scraping noises when running. This even when there were  no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.  

Kevin J. Reynolds.

place inside of dryer

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

Finding parts for very old appliances (that otherwise are working great!) was very much appreciated...lint filters are very very important and this one has served it's useful life. Thank you for such an amazing parts inventory, good prices, and FAST delivery!

Backwards to start- here's the correct way.Disconnect power and vent hose-tip onto front-remove bottom plate allowing access to bottom of dryer and the belt pulleys-remove the small plate in center and under that is a C-clip holding the drum shaft in place-remove the clip and washer-sit dryer upright - open the door and remove the 4 screws under the upper lip which hold the top of the dryer in place-lift up top and secure or have someone hold it up.-inside the top front on both sides are 2 screws per side and there are 2 screws at the bottom under the kick area, remove all 6 of these screws and the front of the dryer will come off-watch the wires-with the front off you can pull the drum forward to allow installing the new belt. - hold the new belt in place with a couple of pieces of tape-reverse the procedure to put drum back together and then thread the new belt onto the drive pulley and under the idler tension pulley.- reinstall back plate, vent hose, power and you're ready to go have a beer.

I looked on the internet for instructions to take the dryer apart,took the parts out one at a time ,and replaced them.It was easy and it made the dryer quiet again.I could see the obvious wear on the parts.I was happy to save the money a new dryer would cost.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

Opened door and found recessed screws that screw into the top of the dry and removed them and then the front removed very easy. Then took of the plate on the back of the dryer to get to the pulley that the drive belt was on and took the belt off the pulley. The dry drum then slid out very easy, there was 2 of use which helped with the ease of getting the drum out. We replace the bearing and the idler pulley wheel. Vaccummed the lent out and then put it back together. Now it is squeek free.

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

replaced rear drum bearing kit Still makes the same noise