DLL2900MNL Hotpoint Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Concord, MA
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter showing signs of wear. Can it be replaced?
I wanted to be sure a replacement would be available when the need arose. The dryer might be 30+ years old. Within a very few minutes I found the filter and placed an order. It arrived in 2 days. Now I won't have to worry about it in this aging lifetime.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Perry, FL
- Parts Used:
- WE12X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
broken belt
Took the top and front off. DO NOT TAKE DRUM OFF!! Lifted drum slightly and worked belt around drum. Replaced front and top. Took off rear panel at bottom near vent pipe. Put belt around motor and then tension pulley. Buttoned everything up and that was it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from CEDAR RAPIDS, IA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out
Unscrewed the old bulb using the lefty loosey method. Installed the new bulb by turning it clockwise or righty tighty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from Hicksville, NY
- Parts Used:
- WE12X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer suddenly start making a rattling noise
I follow the easy instruction by a user in your web site to reach the problem area and discoverd the drive belt was broken.
As it turned out, the problem was compounded when I discovered also that the Heating element needed replacement.
At this point I decided it was time to let go and got a new dryer, choosing the same brand that lasted 25 years: GE
As it turned out, the problem was compounded when I discovered also that the Heating element needed replacement.
At this point I decided it was time to let go and got a new dryer, choosing the same brand that lasted 25 years: GE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Williamston, MI
- Parts Used:
- WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Belt Broken that turns the drum
First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack between the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- audrey from WHITING, NJ
- Parts Used:
- WH01X10106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
dryer shut off and would not go back on
After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell P. from Dushore, PA
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Noisy Bearing "SWEEKING"
The first thing I did was move the dryer out so I could "unplug it" !
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Deerfield, IL
- Parts Used:
- WE14X215
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
No heat from dryer. Diagnosed by others as the Gas Valve
Watched tecnician (I paid) as he diagnosed the problem. Four screws take of the top and front. Clothes drum slides out. Access to valve is good. Valve attaches to feed via compression fitting. Male end of fitting on unit is moved to new unit via allen wrench. Drive belt is re attached around drum and over idler easily. Part cost $90.00 shipp0ed to me. Technician asked $375.00 for this repair. Access the parts via placing the model number on Google Search.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffry from ROCKVILLE, MD
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burnt out bulb
Used a flash light to see, reached in and installed new bulb above the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEOMINSTER, MA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb was intermittently working
Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Wynnewood, PA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb dead
remove the old one and put the new one...!!! Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Monroe Township, NJ
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb
Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.
on the inside is the bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from CLOVER, SC
- Parts Used:
- WE18X26
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had a hole in the screen.
Replaced filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Rochester, NY
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Drum was squeaking and making a lot of noise!
Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.
Was this instruction helpful to you?
Thank you for voting!