HTDX100GM8WW Hotpoint Dryer - Instructions

The part was delivered in record time. That was the best part. And it fit perfectly and was the correct color. The other filter was grey and the dryer is white. Thanks for being so efficient.

Ordered new lint filter, received it in 2 days, removed old filter, snapped in new filter, patted myself on the back .

My dryer knob broke on the timer cycle switch so I ordered a new one along with a new dryer knob which didn't fix the problem, then I ordered the start switch and all I had to do was remove the back of the dryer where all the knobs are located and remove the start switch by turning the start switch to remove it, replace it with the new one by turning it till it clicks in just like when you removed it, put knob back on the front. However that didn't fix my dryer either so I ordered the thermal fuse and switched it out and that was what started the dryer back up. It is located on the back all the way to the bottom where the electrical cord is. Remove the cover and locate the fuse. Use a pair of pliers to pop it out and push the new one back in.

Advice from others with same problem on your web site was very helpful. I removed one of the three torx screws holding the deflecter, Used 2.5 star-drive screw diver bit and cordless drill/driver. Replaced 2 of three torx screws holding the deflecter with the headless brass screws, Using vice grip to tighten. Removed third torx screw and removed old deflector. Used shop vac to clean behind it. Installed new deflector, sliding it over the 2 headless screws, then installing one of the torx screws, then replacing the brass screws with original torx screws, one at a time.

First I called to get help with the right part and they told me I needed the pus-to-start-switch. It came in and I called my handyman Ed to install it. I am happy with your service. I dont install but just got the part in.

snapped in new latch

The timer knob was stripped, so it was stuck in the off position. Ordered the "D"-shaped knob and just placed it on the connector and everything is working find.

Unplug dryer, remove screws and panel. Take picture of dryer motor so you will put wires back the same way . Remove screws using Allen wrench, then unplug wires put the new motor on secure, then put wires back on. View the photo make sure the wires are the same. Then plug your dryer back up. And Happy drying..

Slid off the old part and slid back on the new

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

I watched how to do the repair on YouTube prior to ordering the parts. The video seemed simple enough so I ordered the parts and followed along with the YouTube video. My new push to start switch did not work properly, still had to rest a heavy object against it to get the dryer going and my timer knob worked for a full cycle and a half before it stopped working. It became loose and will not set on any specific time setting. Perhaps I diagnosed my problem incorrectly, not sure just know I am out of $96.06 and am grateful that I have a clothes line strung up outside to dry my clothes for now!

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.