HTDP120GD5WW Hotpoint Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- syd from wilmington, NC
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no handle
just replaced the unit handle and how my wife can open the dryer without a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from OLD TOWN, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher
Replace both micro switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tallahassee, FL
- Parts Used:
- WE4M519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Start Switch Replacement
It's no surprise that GE would use cheaply made parts in such a mass produced product, but it was irritating to see the start switch fail just fourteen months after purchasing the dryer. I am glad that a little thought was put into an easy snap and twist installation of the control panel switches. The original switch failed, due to arcing and pitting of the contact points no doubt, and the local parts house didn't even recognize the part, let alone have it in stock. Thanks to PartSelect.com I could have the part in just a couple of days!
The panel comes appart with just four star driver screws on top, but an allen wrench will work also. Wire jumpers with spade connectors are pulled apart and reattached with needle nose pliers.
In the mean time to keep the dryer operational, I did some creative "re-assigning" of some of the control panel jumper wires using the switch that controled the "Wrinkle Care" setting as a temporary Start Switch as it had the same current handling limits. By the way before attempting such a temporary bypass setup, consider not voiding any warrantee arrangement still applying to the product and have some basic electronics and safety knowledge, study the provided schematic well attached to the back panel and remember to write down all of the original wire connections. And when in doubt, calling a qualified GE appliance repair person is your best and safest bet.
New part went right in in about 15 minutes with original wiring restored and double-checked and the dryer is running right on que again.
Thanks PartSelect.com!
The panel comes appart with just four star driver screws on top, but an allen wrench will work also. Wire jumpers with spade connectors are pulled apart and reattached with needle nose pliers.
In the mean time to keep the dryer operational, I did some creative "re-assigning" of some of the control panel jumper wires using the switch that controled the "Wrinkle Care" setting as a temporary Start Switch as it had the same current handling limits. By the way before attempting such a temporary bypass setup, consider not voiding any warrantee arrangement still applying to the product and have some basic electronics and safety knowledge, study the provided schematic well attached to the back panel and remember to write down all of the original wire connections. And when in doubt, calling a qualified GE appliance repair person is your best and safest bet.
New part went right in in about 15 minutes with original wiring restored and double-checked and the dryer is running right on que again.
Thanks PartSelect.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MATTHEW from LIBERTY, SC
- Parts Used:
- WE4M519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer Would Start Automatic Without Using Start Switch
Remove top control panel, disconnected wire from old switch to new switch (remover 1 wire at time so it would not get mixed up)twisted old switch out inserted new switch and replaced control panel now works like it should. I thought it might would be a safety issue is why I replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Monroe Township, NJ
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb
Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.
on the inside is the bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from ROYAL OAK, MI
- Parts Used:
- WE4M519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Start switch was stuck in the on position internally. By the way this is for a gas dryer not listed in your appliance type
Un plugged dryer from wall - pulled off knob - Unscrewed 4 screws on top of panel - Opened panel by pulling it forward - Removed 2 leed wires - removed switch by turning switch counter clockwise - installed new switch put the wires back on and screwed the panel back on. Done deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from EDGEWATER, FL
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My last phase of repairs of minor items.
if your unit has over 6,000 hours of operations, one needs to remove the front panel and inspect the sliders that the drum rides on. The video were very helpful to replace the sliders. Unfortunately, my dryer had over 10,000 hours of operations over a 30 years period, hence a major repair costing over $200.00 dollars. The drum sliders were gone, hence the drum eat through the plastic guides. More so, the drum started to eat away the front panel. If the dryer is eating your closes and making a noise, one is looking at a $200.00 repair job. Hence check the sliders early will save one $$$$.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CAROLINE from SAN ANTONIO, TX
- Parts Used:
- WE1M652
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke
Very simple. Ordered the part. Received correct part and fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BIRMINGHAM, AL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Timer knob stop working
Just took off old one installed new one. It came right on. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffry from ROCKVILLE, MD
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burnt out bulb
Used a flash light to see, reached in and installed new bulb above the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from ALLEN PARK, MI
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knob broke and ordered a new one
Very easy fix since it was only the knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from HAWLEY, PA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke
Snap off and then snap New one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEOMINSTER, MA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb was intermittently working
Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TAMPA, FL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The small clip in the Timer Knob was broken and the Knob would not turn the timer.
First I took the system apart which I did not have to do. However, by doing that I was able to figure out which parts make the timer run. Anyhow, you simply place the new timer knob on the small shaft and it worked like magic. It was very easy to do.
Was this instruction helpful to you?
Thank you for voting!