HTDX100GM7WW Hotpoint Dryer - Instructions

Popped off old knobs, popped in new. Sorry, nothin' to it or I would'a yelled HELP!

I first removed the the timer knob and the other ones from the front of the control panel. Then I removed the three screws that held the rear access to the control panel. Disconnected all wires to the timer keeping written info to which wires went to which terminal. The replacement timer was exactly like the original in the placement and designation of the terminals. I then twisted the bad timer out of the plastic holders, placed the new one and twisted it in place, and replaced the wires. I then replaced the screws in the rear of the panel and replaced the knobs. It did not take much longer than writing this. Very easy and I am completely satisfied.

Very easy! Removed old parts, and installed new parts in reverse order. Dryer was running, and sounded like a new appliance in 35 minutes!

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my opinion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!

On my 80th Birthday my son and I replaced the timer. We removed the screws from the back panel. Disconnected the dryer from the electrical outlet. Removed the knob from the front panel. Pulled out the timer and took a picture of the wires connected to the timer. Then we transferred each wire one at a time from the old timer to the new timer. Then we replaced the timer and reconnected the knob on the front. Closed the front panel. Replaced the back. Then for the moment of truth: we set the timer for a few minutes and pushed start. A few minutes later the buzzer went off and the dryer stopped. And we both screamed and praised the Lord. We had never done anything like this before

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

I just removed old parts And put the new part on it was very easy to do.

Replaced the rear drum bearing, Front drum bearing,front bearing tabs and belt. I replaced the belt from the front of dryer. Better to go thru the back. Much easier.

remove the broken one and replace it with the new one

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

Follow YouTube "how to change dryer's belt" some video is very clear.

Replaced High limit thermostat per video on the website. However, the flange of new thermostat is flat, while chassis it mounts on is round to conform to drum of dryer. So new thermostat was not flush with chassis. Dryer did not shut off early (that problem solved), but instead continued to dry clothes beyond time necessary. Note that old thermostat had one side of flange slightly bent and probably more flush with chassis, and better able to sense when hot temperatures were reached. I dismantled dryer again, slightly bent new flange, re-installed. Seems to work better now .

If your dryer is making a grinding or loud plastic rubbing noise, you likely need to replace the slides. Here is how I did it.

TIP: Before beginning, set out a hand towel on the washing machine to set the screws onto, in the order and position you removed them.

IMPORTANT: Before beginning, turn off the gas to the unit and unplug it! This repair is all done from the front side of the machine, so you should only need to slide it out enough to unplug it.

Step 1: Remove the control panel

To do this, you need to pull out on the round silver control knob to remove it. This will expose a long screw. With the long screw removed, grab the panel with both hands and slide it straight up. Be careful, the control board is still connected with a 40-pin ribbon cable. Set the control board on top of the dryer temporarily.

Step 2: Remove the lid

There are three screws to remove the lid. Remove them and set them on the screw holding towel. The lid is attached at the back, so to remove it you need to slide it forward towards the front of the unit. Once the lid is loose, you can have a helper hold the control panel while you set the lid aside, or gently let the control panel dangle.

Step 3: Disconnect the control panel and wiring harnesses

Gently pull on the 40-pin ribbon connector until the control panel ribbon cable is removed. There is a notch to designate which direction the ribbon cable it goes back in. Set the control panel to the side. At the same time, you can disconnect the two wiring harnesses that feed the door light and sensor. These wiring harnesses are secured to a silver plate with a zip tie. Cut the zip tie with your diagonal cutters. (You can trim the old zip tie and replace it by feeding the extra small zip tie through the original opening later.)

Step 4: Remove the steel plate that the wiring harnesses were attached to

There are 6 screws to remove the steel plate. Pay attention to where the extra large head screws go, because these are what the control panel slides onto, when you put things back together. Pull out on each side to release the bottom clips, then slide it upwards. Set this piece aside.

Step 4: Remove the front panel (the door panel)

There are 4 screws to loosen the door panel. Two silver screws at the top, and 2 white screws at the bottom. Loosen the white screws about half way. These do not need to be completely removed because the door can rest on them. Remove the top silver screws. Gently lift the dryer drum off the front bezel while you tilt the front panel towards you. At this point you should be able to see the white and dark green slides. I found it easier to lift the front door off the white screws and set it up against the wall.

Step 5: Replace the slides

The slides have plastic hooks that go through the round holes on one end to hold them in place. You should be able to remove the slides with your fingers (maybe with a little help from a flat-head screwdriver), and replace them. There are dozens of YouTube videos on how to do this if you need help. Be careful not to break the plastic hooks that hold the slide to the front plastic bezel. Replace white slides with the white, and the dark green slides with dark green.

Step 6: Putting it all back together

Do everything in reverse. Set the front panel in the white screws, lift the drum, and slide the door panel back to rest on the slides while you put back the silver screws. Give the drum a few good spins manually to make sure there isn't anything still rubbing. Keep in mind the sliding noise is slightly louder than normal until all the panels are replaced.

It will help the process to only tighten the screws half way while putting them all back in. Once everything aligns, then you can tighten them down. DO NOT over tighten, use hand tightness only or you will strip them out. With the front door panel back on, you can put the steel panel back in place. Once you have the 6 screws done, remember to slide a small zip tie through the previous hole to secure the wiring harnesses. Connect the harnesses, and the front panel ribbon cable before putting the lid back on. Insert the screws to the lid, then slide the control panel back down, and replace the single long screw. Note that the control knob is notched, so align the flat sides as you put it back in.

Plug it back in, and turn back on the gas, you are done!