NVLR333EV0AA Hotpoint Dryer - Instructions

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

Boyfriend did the repair but it took very little time, the dryer now runs nice and quiet with no thudding and all my clothes are safe from being eaten!

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Pull old one out stick new one in. Less than 1 minute. Last repair was the water pump that was easy.

My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.

On arrival at rental in Florida, knob & half of shaft are on top of the dryer. Thanks! It's fixed

Pulled old lint filter frame out and replaced with new one, very simple. works like new.

I removed the rear panel to access the drive belt. Lowered the pulley to remove the belt and then took off the front panel and popped the top lid off. The belt was slightly frayed on the edges and looked a little old. Inside of the dryer was filled with lint, noticed the vent that sucks the lint from the dryer was almost totally blocked because off caked on lint. Probably from the moisture when we lived in Tx and had it in our garage. Sucked it out with the shop vac and scraped the rest. Removed the whole drum and that's when I noticed the rear drum bearing was totally destroyed and only a piece or two remained. Ordered the drum bearing and drive belt. I was about to put them on when I saw the drum slides were worn pretty thin. So I had to order more drum slides. That's why it took me so long to repair the dryer. If I had the parts already, it would have only taken an hour or so. I was pretty excited that I did it myself, since my husband usually fixes everything around the house. Easier than I thought :o)

With my hands, a 2 yr old could of done it. But I was amazed how quickly I received the part. Thanks

It was very easy. Pop out old, connect new wires and done! Can't say enough as to how fast and easy getting the part from this company was. Ordered the part later in the day one night and on the second day the part was there. Outstanding service.

i removed two screws and lifted the top up on it hinges. the heating coil was readily accessible. luckly one of the thrmostats fell apart.
partsselect was great. exploded diagrams let me locate and order the replcement easily.

thanks to partsselect i can keep my 16 year old dryer forever.

I repaired it by logging on to parts select website and found the part, waited for about a week or so and opened up the box. I glanced at it and found out that wow it's the exact match except new. Unbelievable and in excitement I went to my laundry room and opened up the dryer and popped that baby right in! Thanks Parts Select

first I removed the screws with the nutdriver at the bottom of the dryer at the back..then I could see the belt was broken...next I took off the 2 nuts at the back that hold the top on ..then opened the dryer front door and unscrewd the 4 screws holding the top on....then I lifted the top up and to the side...then all I had to do was take out 2 screws one on each side of dryer front and the the front was open enough that I could slide the new belt on dryer..then screwed the front back on...then placed the top on and went to the back of dryer and put belt on pulley using the diagram I found in the instructions inside the dryer top...really a lot easier than it sounds...easy fix saved me from buying another dryer

Easy. Take old one out, put new one in.

Took to many parts off to find out only needed to remove four front screws under the lid. I lifted the lid and found the thermostat and replaced same dryer now works great again at normal temps.