HTDX100GD1WW Hotpoint Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christel from GREENACRES, FL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The timer knob was inoperable
Very simple: I looked up the part number for my timer knob, ordered it from this site and received it one day earlier than expected. I simply attached the knob, and my problem was over. I am very, very satisfied and happy with your immediate delivery of the ordered part.
Was this instruction helpful to you?
Thank you for voting!
The start push button and the timer knob were broken because of low quality parts.
These buttons are easy to fix. Just line them up with the D shaped shaft and push the buttons to get them to go on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from BATESVILLE, IN
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
unable to select anything on the wash cycle selector
the original knob had cracked and I ordered a new one and replaced it, all is well, thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor from ST AUGUSTINE, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
door filter
was no repair- removed filter from door and installed new filter into door. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGIA from SAN DIEGO, CA
- Parts Used:
- WE04X20415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Knob broke because Timer stopped working
Ordered & received new Timer & Knob. Disconnected dryer from power.
Located screws on back of dryer console & removed screws so console could be tilted forward.Used cell phone to take picture of timer with connections to keep track of where to reconnect wires. Unsnapped connections to timer. Removed old timer and attached new timer. Attached new knob to front of console. Plugged dryer back up to power and tested by turning new knob. Reattached console with screws. Done!
Located screws on back of dryer console & removed screws so console could be tilted forward.Used cell phone to take picture of timer with connections to keep track of where to reconnect wires. Unsnapped connections to timer. Removed old timer and attached new timer. Attached new knob to front of console. Plugged dryer back up to power and tested by turning new knob. Reattached console with screws. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salem, MA
- Parts Used:
- WE03X29897, WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Rear drum bearing gone (only 4 years old). Decided to replace belt while I was at it.
I first watched the video on how to. Being mechecanically inclined I dismantled and removed everything needed to replace the drum bearing. Also removed belt at the same time. I replaced the bearing, then the belt. The belt could be a little tricky for some people. Getting the belt on the tension pulley could be a problem. What I did was I got a large nylon tie and put it around the armature of the motor. I then retracted the pulley just enough to be able to slip the belt over it. Of course this is all performed through the limited space on the bottom left, between the drum and the dryer shell. Once on the pulley, I cut the tie with wire cutters and it snapped into place. Rotated the drum a couple of times to line the belt with the pulley, perfect. I then put everything back together. I also cleaned any and all the lint that had gathered throughout the exhaust. Pluged the dryer in, perfect. Just like new. One more note getting the parts was so easy also. Your website and how to demo was a great help. Thank you, thank you very much. The words of the late Elvis Presley. They never get old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TAMPA, FL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The small clip in the Timer Knob was broken and the Knob would not turn the timer.
First I took the system apart which I did not have to do. However, by doing that I was able to figure out which parts make the timer run. Anyhow, you simply place the new timer knob on the small shaft and it worked like magic. It was very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BIRMINGHAM, AL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Timer knob stop working
Just took off old one installed new one. It came right on. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laurel Springs, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Forrest from Mays Landing, NJ
- Parts Used:
- WE14X25080
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Cracked air duct
Two screws under the dryer door then the top comes off.Then two screws hold the front on come out. 4 screws top is off and front is off the rest is no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from LIMA, OH
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Put the knob on and turned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from CRAWFORDVILLE, FL
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
knob broke
Just pushed on new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LEONARDTOWN, MD
- Parts Used:
- WE1M652
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob fell off. Had a crack in it.
Opened the package. pushes the new knob on and voila it worked! It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from ALLEN PARK, MI
- Parts Used:
- WE1M652
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knob broke and ordered a new one
Very easy fix since it was only the knob
Was this instruction helpful to you?
Thank you for voting!