NVLR223PJ1WW Hotpoint Dryer - Instructions

Deflector has 3 bolts attaching it. They require a star wrench. Had to purchase same to do the repair. Removed the bolts(they are sheet metal type screws(bolts). Installed the deflector and started dryer. Loud rubbing sound noted. Shut off and checked the drum and noted it was not running concentrically. Removed deflector and the found the 3 screws actually retained the drum to drive. Had to make alignment pins to allow proper alignment of the drive, drum, and deflector. Once the pins were used during installation of the deflector everything worked correctly. Turned on dryer and it operated normally.
Had I had the proper tools the repair would probably have taken 30 minutes or less.

Someone I'm related to by marriage accidentally dried a plastic-coated tablecloth on high heat, and our heat deflector was hosed. I was very happy to find this part here for such a reasonable price; Sears wanted about $65 for it. Installation required a Torx bit, and removing the old one was easy, but the dryer's design made it difficult to reinstall the heat deflector while keeping the dryer running concentrically. I ended up cutting the heads off three screws, threading those into the plate behind the drum, sliding the new heat deflector on over those, and then one by one replacing them with the original Torx head screws. Once I figured it out it didn't take long but it took me a while to figure it out. That's probably more a reflection on me than the dryer!

First I had to remove the top by taking out the two screws inside the door. Then I removed the front by taking out the two screws holding it from the inside. I needed to remove the drum and to the the belt off, I removed the left side. It has several screws down the back, two on the bottom and two in the front. I removed the belt and drum. I took out the old sleeve bearing. Part of it was broken off into the hole it goes into. I then had to remove the plate that holds the heating element. Once that was done, I put the new bearing on and replaced the drum slides on the from section. Then I reversed the process to reassemble. Not too bad.

Everything is cleaned as it is removed.

Remove the two screws holding the top down.
Disconnect two wires from door switch.
Remove the two hex screws holding the front on.
Remove the 4 screws holding the access panel on the back and disengage idler pulley to loosen the belt.
Remove the drum.
Label the wires then remove the heating element.
Check orientation of ground strap before disassembling rear bearing.
Remove four screws holding rear bearing to back of heating element.
Install rear bearing and ground strap on to heating element.
Reinstall heating element.
Reconnect wires.

Most Important : Get help putting parts back on drum! I didn't and that's why it took over 2 hours.
I will describe how I did it.

Unscrew bearing from inside of drum.
Wrap screwdriver with tape to a little larger than the screw hole.
Use small screwdriver to line up the drum, shim and deflector.
Don't forget the brass shim. It wasn't on the parts diagram.
Start two screws don't tighten them yet.
Remove Screwdriver and start third screw. Tighten all three down.
Put belt on drum.
Install drum and belt.
Reverse disassembly.
When putting the front on make sure drum rests in the felt.

I rated this a bit difficult because I did it myself. With help this is a fairly easy repair.

straightforward swap, just form the top rail and click it in

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.

I bought a natural gas orfice for a dryer that needed to be change from Lp gas. I was able to
change the parts,it was very helpful that there was a drawing in the package showing the
location of the parts that need to be changed. This was a used dryer I purchased and
I did not have an owners manual to refer to.
Everything went very well, Thank you.

Marcia

I followed the directions that were listed on this site by other Do It Yourself individuals...by the way I'm a lady and more mechanically inclined than my husband, but he was a great help in lifting the drum up and out. (I unplugged the dryer before starting repairs)
1. I removed the two screws located at the top of the dryer inside the door.
2. Top of dryer cabinet lifted up after screws were removed.
3. Located and removed front panel retension screws and removed front panel and set aside
4. slipped belt off motor by reducing tension on idler pully
5. Removed screws inside drum that secured drum to bearing assembly
6. Husband and I lifted drum up and out of cabinet (this went very smoothly and took less than 15 minutes time.
7. Followed supplied bearing drum instructions and removed old bearing and installed new assembly.
8. Thoroughly cleaned out internal cabinet, blower, and motor areas
9. Reset the idler pully into proper position.
10. Tipped dryer on 'back' to reseat the drum With A NEW DRYER BELT (taped temporarily around the drum) into the bearing shaft (I may not be using the proper terms)
11. tipped dryer upright and while Hubby balanced the drum, the front panel was resecured to the rest of the cabinet.
12. Removed temporarily applied tape that held the drum belt in the general position, then using the rear access panel, I slipped the belt over the motor into the proper posisiton.
13. Top cabinet was reapplied and screwed into
place.
14 Plugged in and tested the dryer...NO SQUEAKS and it works beautifully and quietly!!

The job is not terribly difficult, but I am only 5 feet tall and the drum is bulky to work with and balance. Reaching into the cabinet to slip the belt onto the motor stretched my arm to the limit.
I found the cabinet reassembly and realignment of the screw holes quite annoying. But the total job proved satisfying upon completion.

I removed the top of the dryer (unscrewed from the inside to release the top). Removed interior screws to pull open the front of the dryer. Once inside, it was really visible that the old parts (front air duct top and bottom) were in bad shape. They were cracked and broken. I removed the old pieces (they pretty much cracked and crumbled right off). I snapped in the new pieces careful to avoid damaging the electrical connections and wires. Once snapped into place (top and bottom), I careful put the front back into place making sure that the dryer drum rested on the new pieces. All screws back in place and all done! Dryer is now working as new!!!

I removed the door and "flipped" it to open right to left. Rather than remove the existing door latch I added the purchased latch on the right side to enable opening the door right to left or left to right.

Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !

Inserted handle into slots

Replaced cycle thermostat.

my problem was easy, i orderd a new lint filter, for a
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......

Disconnect Power from the Dryer
Remove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unhooked the belt from the tensioner and motor pulley.
Pulled the drum out. Removed the belt.
Removed the three screws that held the bearing assembly
on the back of the drum.
Removed the keeper o-ring slide the bad bearing off of shaft. Slide the new bearing on the shaft put the new o-ring on the shaft. Reassembled the bearing on back of the drum. Put belt back around the drum and put drum back in place. Put The belt around the motor pulley and tensioner
(this is probably the hardest part).
Put the front and top back together.
Turned the power back on. Job done