NLLR113ET0WB Hotpoint Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- frankie from east windsor, NJ
- Parts Used:
- WE01X20419, WE18X54
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door handle was broken off and i needed a new lintfilter
door handle just snaps right in and the lintfilter is a no brainer. thank you very much partselect keep up the good work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Santa Barbara, CA
- Parts Used:
- WE4X197
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer would not start
I checked the power (OK) and removed the four screws that held the timer/controls (upper panels) cover. This revealed a schematic for the dryer that enabled me to determine the door swich was probably the culprit. I pried out the old switch and, sure enough, it was always open (checked with multi-meter). I found the replacement switch easily using the dryer model number and "door switch" search string. Ordered Sunday night, the part came on Tuesday and took 2 minutes to install (no tools needed).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Kingston, OK
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door would not stay closed
It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Old Town, FL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Handle
Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from ORLEANS, IN
- Parts Used:
- WH1X2756
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer knob broke
This story first. I went to local hardware where I purchased the dryer over 10 years ago and asked them if they could get me a new knob. I had the model number and serial number. They said sure can, but they are expensive. They told me that the knob was around $20. and that the shipping would be $10-$15. . Both was under $14.00 at this site. Just alined the knob up on the stem and pushed it on. THANKS!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Richmond, KY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken dryer handle
My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Huntingdon, PA
- Parts Used:
- WE9M10, WE3X87, WE3X77, WE3X75, WE12X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
dryer made screeching noise when running
removed top by removing two screw inside door,
found felt was out of place and ruined--found some wear on bearing at rear of drum--decided to
replace these parts plus fround bearing--also
new belt ,since it was apart---to remove the drum
you have to remove front panel,which required
removing two bolts from inside at top--front of
dryer just lays down--then you can pull tub out-
I read other customers repair storys ,which made it real easy.
found felt was out of place and ruined--found some wear on bearing at rear of drum--decided to
replace these parts plus fround bearing--also
new belt ,since it was apart---to remove the drum
you have to remove front panel,which required
removing two bolts from inside at top--front of
dryer just lays down--then you can pull tub out-
I read other customers repair storys ,which made it real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STAN from UPPER ARLNGTN, OH
- Parts Used:
- WE1M1011
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic housing for the door latch mounted in the chassis of the dryer was damaged so the section of the latch in the door wouldn't align.
This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mavis from winnemucca, NV
- Parts Used:
- WE3X77
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Bearing was cracked and eating all my clothes
Boyfriend did the repair but it took very little time, the dryer now runs nice and quiet with no thudding and all my clothes are safe from being eaten!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from abilene, TX
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old bearing completley gone; shaft eating through race making a horrible noise when running
pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Beverly, MA
- Parts Used:
- WE18X54
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint basket had hole
Pull old one out stick new one in. Less than 1 minute. Last repair was the water pump that was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Bradenton, FL
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic shaft on switch broken.
On arrival at rental in Florida, knob & half of shaft are on top of the dryer. Thanks! It's fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Charlotte, NC
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer would not start
My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from lake hiawatha, NJ
- Parts Used:
- WH1X2756
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the knob had cracked after 12 years of service
i placed the knob on and voila it worked again. the knob was a bit pricey with shipping almost 25.00 but the dryer is 12 years or more old and it is the first repair i had to make so i am very pleased with the dryer and the new knob! the on line photos made it very easy to make sure i was ordering the correct knob with all the views. keep up the good work! very satisfied!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Jackson, MI
- Parts Used:
- WE18X54
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter was old and cracked, wore out
Pulled old lint filter frame out and replaced with new one, very simple. works like new.
Was this instruction helpful to you?
Thank you for voting!