NVLR223GF1WO Hotpoint Dryer - Instructions

Removed the broken handle from the dryer and popped on the new one.

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

Open it up. Try to fix with duct tape. Test. Fail. Order parts.

Put slides on, open it up, put parts on door, align drum, close it up.

Start, smile and BRAG!!!!

Works faster, fluffer clothes and I'm a happy Mom because now I can run whenever and there is less wrinkles.

I received the part in record time.(2 days) I had a little trouble getting the case off of the dryer, but the part was real easy to install. I have changed these before with another company and their instructins were not good at all. Your instruction were relly easy to understand, step by step.

Thanks

We removed two screws to remove the top and two screws to remove the front. The dryer drum slides were easy to replace and the felt fit into a track. It was so easy and now my dryer is quiet again, no more rubbing/squeaking. I can't believe that was all we had to do, and for $60.00!!! I'll be back for future parts if needed. Thanks.

The part was delivered in record time. That was the best part. And it fit perfectly and was the correct color. The other filter was grey and the dryer is white. Thanks for being so efficient.

Ordered new lint filter, received it in 2 days, removed old filter, snapped in new filter, patted myself on the back .

First I called to get help with the right part and they told me I needed the pus-to-start-switch. It came in and I called my handyman Ed to install it. I am happy with your service. I dont install but just got the part in.

Advice from others with same problem on your web site was very helpful. I removed one of the three torx screws holding the deflecter, Used 2.5 star-drive screw diver bit and cordless drill/driver. Replaced 2 of three torx screws holding the deflecter with the headless brass screws, Using vice grip to tighten. Removed third torx screw and removed old deflector. Used shop vac to clean behind it. Installed new deflector, sliding it over the 2 headless screws, then installing one of the torx screws, then replacing the brass screws with original torx screws, one at a time.

There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that and you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.

snapped in new latch

I removed the top of the dryer by removing two screws located under the front lip of the dryer over the dryer door. Then I removed the dryer door by removing the screws holding the hinges. I then removed the front panel of the dryer by removing the two screws at the top inside two corners. I the removed the old Dryer Drum Slide. The Drum Bearings were almost completley worn off. I installed the (4) new Drum Bearings (2 Clear or White and 2 brown) the same way they were installed on the old Dryer Drum Slide on the new Dryer Drum Slide. I then installed the Dryer Drum Slide the way I removed the old one. Then I pulled the old Lower Front Drum Seal-Felt and replaced with the new one. Works like new!

watched the video on your website,this made repair to the dryer very easy.hardest step in the repair was getting the belt hooked up on motor and tensioner,but being old and persistent i finally won!

Open the dryer door and remove the two screws in the top of the door opening that hold the top of the dryer on, and then remove the dryer top. On the inside of the dryer, there are two screws that hold the front of the dryer on. Remove one screw from each side of the dryer near the top, and the front of the dryer will fall away. The drum slides are visible when you lean the front panel of the dryer out away from the drum. You can replace the drum slides without even removing the front of the dryer completely. Pull out the old drum slides and insert the new slides. Lift the drum slighly from the inside through the dryer door as you tilt the front back into place. Reinsert the screws holding the front of the dryer on and tighten. BE CAREFUL not to drop the screws or you may have to disassemble the dryer to get at the dropped screws. Reinstall the top of the dryer. It is a difficult fit which requres inserting into 3 tabs and sliding the top into place. Check that the top is flush before inserting and tightening the screws in the top of the door opening.

A quick look inside verified that the drum slides were worn through but I also found that the plastic drum bearing that holds the slides was cracked in a couple different places. Ordered a new drum bearing, new slides, and decided to replace the felt seal as well since it looked pretty ratty. Parts arrived quickly after ordering and installation literally took 15-20 minutes. Purrs like a baby now. Steps: Unplug dryer. remove two screws which hold top of dryer to front. Remove two screws which hold front (door) to rest of unit. No need to disconnect wiring to front door, just make sure not to pull the wires out! Install new parts. Put it back together in reverse order.