NVL333GB1WW Hotpoint Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Spencer from Chicago, IL
- Parts Used:
- WE25X10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Stackable washer & dryer
Scared to do the work myself found this website which gave me basic instructions and access to parts needed. Ordered and made an error called and CS took care of me right away. Fast friendly and will buy from them again. Great service great parts and great people!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitsuhiro from Anaheim, CA
- Parts Used:
- WE04X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer runs but no heat
I first checked the heating element by peeking through the peek hole in the front to see if it was turning on. The heating element turned on but gas failed to flow. Next, I checked all sensors including the fuse, they were all fine. This points to the solenoid as the cause of the issue. So I replaced the solenoids and the problem solved. I did watch the YouTube video on how to check the sensors and replace faulty parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Lake Mary, FL
- Parts Used:
- WE12X10009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
noisy belt
Removed top of dryer, took screws out of back of dryer, pulled drum off front of dryer, removed old belt and slid new one in place. Reattached drum to front and slid belt in place only to find it was the wrong size. Called an appliance repair man, he said happens more ften than not.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from San Marcos, CA
- Parts Used:
- 5303937183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
noise
i folow the instructions from web page
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fleming Island, FL
- Parts Used:
- WE03X10007
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer drum seized
Had to pry dryer front off drum because buttons had caught between glide and felt causing excessive heat that melted the glide to the felt. Removed old felt from dryer front and replaced glide then reassembled machine. Took longer overall time because I did not realize two glide parts were needed so repair was delayed until second glide was received.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Bethlehem, PA
- Parts Used:
- WE01X10151
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob selector on dryer cracked - dryer could not be turned on
Still had original manual, went on line with model #, found needed part and ordered it. Part arrived very promptly. Part was installed by hand and problem solved. Dryer now working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENDALL from COCOA, FL
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inoperative Switch
Remove & rplace switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Staten Island, NY
- Parts Used:
- WE12X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the dryer belt broke
very simple my husband put it on in no time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from Blairsville, GA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken post on switch
removed 4 scewws deom case snapped out switch placed the new one attached two wires re attached with the 4 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Norfolk, MA
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
switha broke off
Removed old switch, replaced it with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Edna, TX
- Parts Used:
- WE12X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drum would not turn at full speed, noisy squeak
Top control panel removed; next used screwdriver to lift up dryer top on each side( the top of dryer is attached by clips on the underside) the dryer front panel has two screws, one on each side of inside front(they are easy to reach and near the top of the inside front panel, after removing these two screws we used screwdriver again to pry off front panel as it is attached also by clips on inside of front panel. At this point there is easy access to the drum where the old belt was removed, new belt put in place; removed small panel on back of dryer to access idler pulley and attached new belt through the pulley; turned the drum a couple of times by hand to check if belt was running true on the drum; problem fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Fernley, NV
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was broken and had to use pliers to start dryer
Disconnected the power removed 4 screws from top panel. Removed 2 wires, turned switch counter clockwise. remopved switch. Replaced with new switch,connected the 2 wires, put panel back inplace,put screws back in panel,plugged dryer back in. SUPER SIMPLE Total time 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Ennis, MT
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dryer start switch broken off
Put in the new switch and it starts great. Now that it runs there is no heat. I assume the elements are out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from mcloud, OK
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Something fell off a shelf and broke the switch off
Replaced the start switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Sun City West, AZ
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Sticker Switch Worn Out
Simple replaced switch
Was this instruction helpful to you?
Thank you for voting!