NWXR473GV1AA Hotpoint Dryer - Instructions

Easy repair. Removed top of dryer and removed two screws to front panel and door assembly. Old front air duct assembly was worn and broken, so it literally fell off the panel. I cleaned the front panel and door assembly of all the lint and dirt, and snapped the new parts into place. The new parts came with the gasket and felt drum seal already installed, to all that had to be done was to snap it into place. Installing the drum slides was a breeze. I simply had to slide one end in the slot, position the hole over the pin, and slide the other end in. I put everything back together, and ran a full cycle for test. Dryer works like new, and run quiet.

I initially opened the front of the dryer and noticed that the drum slides that the drum rides on in the front of the dryer were excessively worn. I then removed the drum and noticed that the plastic bearing that supported the drum in the rear was cracked and the washer(?) appered to be disintigrating. I ordered and replaced the drum slides and rear bearing. The dryer was still making too much noise. I ran the motor with the drum removed and realized that they motor was the remaining source of the excessive noise. I then ordered and replaced the motor with a new one and this solved the problem. Total cost was around $140. Note that when ordering a new motor, the instructions on the web site indicate that you need to order the motor pulley if your existing motor has a pressed on pulley. The new motor was a kit that came with the pulley included, and therefore the additional part was not needed, and had to be returned. The instructional videos and parts schematics on the web site were very helpful.

Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a snap.

I ordered parts based off other peoples findings. I took the top and front off the dryer. I found the drum bearing(really only a plastic bracket. The slide were completely worn and the drum was wearing into the plastic drum bearing. I popped the old drum bearing out and put the new on in. There are actually 2 sets of slides (4 total). I only bought 2. I reused two of the existing slides. I put the unit back together and it was a lot quieter. I need to order more of the slides. They are only a couple dollars a piece and take most of the beating. I should've but didn't get the pasking or gasket. It was broken. I think it'll be fine though.

I removed the two screws that hold the front panel to the top panel. I removed two more screws that hold the front panel to the side panels. I separated the front panel from the side panels and removed the drum.

I could see on the front panel the drum slides were badly worn. One was gone.

The new parts installed easily using no tools at all. Everything snaps in place. The new foam gaskets press and stick to seal the duct work. The felt strip pressed into place.

I replace all the panels in reverse order and plug it in. It operates fine, but the motor is making the noise. I will look into replacing the motor next.

Removed the top of dryer two screws behind door at top then removed top two screws top corner lift dryer tub put belt around the tub then looped belt around the pullies.

If you're dis-assembling the dryer panels to remove the drum to acess the bearing located at the rear of the drum,don't hesitate to buy a idler pulley kit and a belt.It's easier to change them now,while it's apart. besides,their all pretty much in the same state of wear! In lew of prying my son away from the computer,an extra set of hands is a help, I used a scrap piece of 4x4 with a 1 inch whole bored in one side to place the bearing end into to steady it to get the screws started. otherwise you need to have 6ft.arms! re-assembly wasn't bad, a magnetic tipped #3 screw driver eliminates the frustration of dropping panel screws down inside the partially assembled body.

Doing some simple troubleshooting with the volt-ohm meter I determined that the door switch was failed.

The replacement door switch restored the motor circuit keeping my dryer in action.

The weight of the front section of the drum in the dryer rides on 4 slim pieces of plastic. remove the screws that hold down the top of the dryer are in the front door at the top at each corner. remove the top, then remove 2 screws that hold down the front of the control panel to the cabinet at the base. remove the 2 screws at the of the front corners of the cabinet to separate the front door section from the rest of the dryer.Watch out for the wires the connect the door to the rest of the dryer. if you replace the bearing at the back of the dryer you need to take two screws out at the base of the cabinet one from each corner to let the sides of the cabinet to spread out and let the drum pass though the front of the dryer cabinet. the belt has to come off the motor by lifting it up an sticking your hand in under the drum and working it off the end of the motor. replaced the parts ad the dryer works like new.

1 Unplug power cord. 2 Remove top and front panels. 3 Remove old bearing, slides and bulb. 4 Install new bearing slides and bulb. Reinstall front and top panels. 5 Restore power and test. Time to repair 25 minutes. Very satisfied with the parts and the time to receive them, very good parts service. Will definately use this service in the future and will highly recommend this company.

Removed lower front panel and then front including door (need to remove the top to access screws.) Replaced both the ingiter and heat detector. The tricky part was getting access to the long tunnel-like bracket that houses the igniter. Washer and Dryer are in a tight cutout space in very small laundry room.

The switch made a humming sound when I turned it so I thought that might be the problem. Using the instructions on this Web site I took the top panel of the dryer off (after unplugging it), unplugged two wires leading from the switch (needed pliers for this), and removed the switch unit by rotating it counterclockwise (when behind it).
The replacement part came in two days. The installation went a lot quicker-maybe ten minutes.

First, I loosened the the top control panel and then loosened the top flat roof panel which allowed me access to the inside of the dryer. Then, I removed the front panel which allowed access to the drum. I was amazed at the amount of lint that was inside the dryer itself. Most of my time was spent in the disassembly and cleaning of the internal cavity around the drum. I reached below the drum and removed the belt from the pulley wheels and then unscrewed the drum (from the inside) from the back of the dryer and bearing kit. I removed the diffuser and cleaned it thoroughly. Then I replaced the entire drum bearing kit - the old one was almost completely dissentigrated. I probably should have applied some kind of non-flammable lubricant to the new bearing kit - the instructions did not include this step but after about 3 loads a slight squeak (different). I put everything back together - applying the new drum kit will require 2 sets of hands (my 9-year old daughter did great at this). I re-assembled the dryer and it works great, again except for the slight squeak that's still there. I may disassemble it again and apply some lubricant but I do not know what kind to get; I need to check that out.

Deflector has 3 bolts attaching it. They require a star wrench. Had to purchase same to do the repair. Removed the bolts(they are sheet metal type screws(bolts). Installed the deflector and started dryer. Loud rubbing sound noted. Shut off and checked the drum and noted it was not running concentrically. Removed deflector and the found the 3 screws actually retained the drum to drive. Had to make alignment pins to allow proper alignment of the drive, drum, and deflector. Once the pins were used during installation of the deflector everything worked correctly. Turned on dryer and it operated normally.
Had I had the proper tools the repair would probably have taken 30 minutes or less.

Pulled the front of the dyer off, snapped old bearing off, snapped new drum bearing in, affixed 2 new slides and 2 new other widgets (5 pieces total). Vacuumed/cleaned out various bits and pieces before i closed her up.

No squeaking.

Called a priest, but he died. Now i just do whatever the demon says, but i do it with quietly dried clothes.