DDE7500BAL Hotpoint Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- PRESTON from CINCINNATI, OH
- Parts Used:
- WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Drum Would Not Turn
Remove the bottom cover of dryer to look at the motor, see belt hanging remove broken belt. Remove screws from the top and front, slide belt over drum put small piece of tape to hole belt in place replace screws go back to the rear pull belt over the motor pulley close back panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Dassel, MN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Dryer squeaked when running
Took the dryer apart to get to the rear bearing. Took the bearing assembly out, kept the e-ring from the old bearing shaft, replaced the bearing kit, took the o-ring off the new shaft and replaced it with the e-ring, then reassembled the unit. Make sure to place a nail or long screw into into the rear of the drum, so that you can realign bearing on the drum. It is easier with two people when reassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Red Wing, MN
- Parts Used:
- WE12X10014, WE12X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dryer not working
First I took the lower bottom off the back of the dryer (bolts), pulled the old pulley off the idler and put new one on. Second, I took the screws out in front (under lip of top) and then removed bolts from bottom of the front. Then lifted lid up and swung front to the side. I was then able to take the drum out and clean it before putting it back in with the new belt. The put everything back together.
Dryer ran for ten mintues and then quite again. Seems to be in the motor and not the less expensive parts I found to be worn.
Dryer ran for ten mintues and then quite again. Seems to be in the motor and not the less expensive parts I found to be worn.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Glendive, MT
- Parts Used:
- WE12X10014, WE25X60, WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
rear dryer bearing assembly not threaded
The rear bearing plate had no threads where the screws go to hold it to the back of the dryer drum. I have never bought anything else that needed threads cut in it to be used as a replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Rochester, NY
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Drum was squeaking and making a lot of noise!
Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Union, WV 24983, WV
- Parts Used:
- WE11X260
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
No heat in dryer
I searched the web and found a site that explained how the unit came apart. Took it a part almost according to instructions (I thought I saw a short cut that wasn't).
Unplug
Remove top, torx screws above door, tilt top back, lift front (swing to the right).
Remove clip from back of drum, and slide the drum out(watch the belt or remove tension first)
Remove wires and restring
Slide belt on to drum.
Slide drum back into dryer.
Reinstall front and top.
Retension belt.
Plug back in.
I took the time to remove the duct and cleaned out the unit before reassembly.
Also it helps if you can get easy access to all sides of the unit. I could not, the owner had stored stuff around it to the point that it would have added several hours to the repair to gain easy access. So I had to do some gymnastics to get to all the area's to work on the maching. It is my Dad's dryer and that is enough to write a novel about.
If I had followed the above, it would have saved me an hours worth of time.
Unplug
Remove top, torx screws above door, tilt top back, lift front (swing to the right).
Remove clip from back of drum, and slide the drum out(watch the belt or remove tension first)
Remove wires and restring
Slide belt on to drum.
Slide drum back into dryer.
Reinstall front and top.
Retension belt.
Plug back in.
I took the time to remove the duct and cleaned out the unit before reassembly.
Also it helps if you can get easy access to all sides of the unit. I could not, the owner had stored stuff around it to the point that it would have added several hours to the repair to gain easy access. So I had to do some gymnastics to get to all the area's to work on the maching. It is my Dad's dryer and that is enough to write a novel about.
If I had followed the above, it would have saved me an hours worth of time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TOM from ATHENS, GA
- Parts Used:
- WE12X10014, WE4X600, WE3X75
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Dryer Wasnt Drying ;Motor Sometimes Not Starting
Disassembled;(mainly just taking screws out) blew/vacuumed 50 pounds of lint from chassis/motor area ; replaced thermostat, and while I had it apart replaced belt and bearing. Runs/dries like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Freeland, MI
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
loud noise when ran for 5 min.
Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from CAMP VERDE, AZ
- Parts Used:
- WE25X60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Squeak when running
Moved the dryer so I had room to work. Took off front of dryer with torx socket. Took off drum belt then able to take out the drum. The glides were worn replaced with two new glides (held in with 5/16 screws). While apart replaced the heater assembly and replacement of the drum belt. Went very well and smooth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ED from BALTIMORE, MD
- Parts Used:
- WE4X197
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door switch burnt -up
1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from CLOVER, SC
- Parts Used:
- WE18X26
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had a hole in the screen.
Replaced filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- audrey from WHITING, NJ
- Parts Used:
- WH01X10106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
dryer shut off and would not go back on
After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from POUGHKEEPSIE, NY
- Parts Used:
- WE4X600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drier didn't run thermostat burnt open.
Open drier door removed lint filter unscrewed thermostat cover unscrewed thermostat removed wire the reversed procedure. Test operates as intended.
Was this instruction helpful to you?
Thank you for voting!