DLB2700LB Hotpoint Dryer - Instructions

Researching on the web I thought the trouble might be lint buildup or trouble w/ one of the parts involved in spinning the drum. However I cleaned out all the lint and replaced the belt and idler pulley and this didn't improve the smell (drum bearing was fine). I then concluded the trouble was the motor. Running the motor w/o the drum in place confirmed this was where the noise/smell was coming from. Replacing the motor was fiddly--I had to remove the clip holding the motor (pried the top w/ a screwdriver), wires (made a diagram so as to put back in same order, they were hard to get off--a pliers did the job), clamps holding the motor on the duct, the motor mount, the duct, the fan. Putting all this back together took a while (not hard just fiddly). Tested the motor w/out the drum in place and it sounded fine. Put the drum and back/front/top panels back and the dryer runs fine now. All parts came quickly and exactly matched the parts in my 1993 Hotpoint dryer. As others have said the pulley kit is not needed--these are included w/ the motor. BTW I am a 53-year-old lady. Thanks to all who took the time to write up their experiences--big help!!

disassembled chassis of dryer, unbolted top, lifted top to expose drum. bolted top back on. resumed repair next morning. unbolted top. lifted drum (it moved up and down about 1 inch) and got new belt around it. rebolted top down. tipped dryer to its back. unbolted and removed panel at bottom, exposing drive motor and tensioner spring. positioned belt around drive motor spindle and tensioner spring. replaced panel. reconnected dryer to electricity. reconnected gas using new flexible connector.

Deftly removed the old lint trap and placed the new frame in place. It worked perfectly. Hands only repair.

I did not have an actual repair. I simply replaced the lint filter that dropped into the receptacle. However, what I want to mention is that the part was available as old as the dryer is and there was a nice photo to scale of the replacement part so that I was sure I was getting the correct piece. A great site to obtain parts from my experience.

Just replaced it with the new one

I only ordered a lint filter with frame but wanted to let other's know that ordering from your site was extremely easy and the shipping was extremely fast!! I received my order with 2 days of placing my order. Thank you!!

Pop off the old, pop on the new. I did it with one hand, the 'hard' part was putting the access panal back on.

place new filter in

no instructions necessary for this part install

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

removed four screws holding top. Swing back top to expose thermostat. emove two push on connectors and two self tapping screws. Instal new thermostat

Change the coil by removing the cotter pin around drum in the back I accidently removed the 3 star bits and the front and it was hard getting back together. The coils are easy to change, but found that the coil wasn't the issue it was the cyclical thermosat underneath the lint catcher in front. The part (heater coil) works better than the older one, so I guess it wasn't a complete screw up. I read up on a few others and think I should have check thermostat first oops. good luck

I have had this happen to another ge dryer, so I had an idea what was wrong. After taking the 4 torx screws out from under the front lip of dryer top, lifting the top back (like opening the hood of your car) in the back right corner is where the high limit tstat is. To verify the problem (dryer already unpluged of course) pull the two wires off the terminals of tstat, connect them together, wrap bare parts w/ electrical tape. Let top down & plug dryer in-- it started& ran fine. Got online and ordered replacement tstat (it arrived in 2 days-- great!) unscrewed the two 1/4" hex screws holding tstat on, installed new part. On to bigger and better things ! Dryer working fine.

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)

I was unsure of how to disassemble the machine to reach the belt, but a YouTube video gave me confidence. Thanks to Partselect.com, the great customer service, and fast delivery. I had my dryer up and running really fast! The process was really not difficult at all and it gave me a chance to vacuum out years of trapped lint. I am so happy to have saved hundreds of dollars, not having to buy a new dryer.I would urge other folks to tackle these relatively simple repairs, the right parts are a phone call away. Frank