GDE546RHS0 Gibson Dryer - Instructions

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

The repair went very smoothly. I'm a woman in my mid 20's and was prepared to buy a new dryer but I saw the part online for a very reasonable price and the video instructions were extremely helpful. I was able to fix the dryer quickly and cost effectively AND the part arrived in only 2 days! It all worked out very well.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

followed video and replaced part( cleaned and vacuumed dryer while I had it apart),relatively easy repair

spoke with repair person he indicated problem was not door switch but control board, prior to repair person arriving I receive the switch in the mail, I unplugged drier used a small edged screw driver to remove door light switch, removed three wire clips from the old switch, re connected the wires to new switch pushed the new switch into its location, closed the door light went out and the drier started and has ran just fine ever since, saved myself several hundred dollars or a new drier

The repair was a bit more simple that what I had read here earlier, to see if I could handle it or I would have to call someone. The biggest relief was that I didn't have to remove any of the connectors from the control panel. Only 4 total connectors were removed at the Heating Element itself. Here's the steps I performed: 1) Pop the top off by prying the lid to release the 2 front clips and lift the top all the way up (like the hood of a car). Rest this against a door or wall. 2) Remove the rear access panel (2 phillips screws) on the bottom left of the unit. Remove the tension from the dryer belt and take it off the pully. 3) Go back to the front and remove (4 allen heads) from the back of the dryer drum. The drum should now have some play. 4) remove a plastic retainer that stops the drum from being lifted out. Now you should be able to lift out the drum. There is a ball & socket fitting that needs to come apart. This can be done by sharply lifting straight up. This gives you access to the heating element and you should be able to see where the coil has burned, thus opening the circuit. 5) remove (4 phillips screws) from the back panel of the dryer. Remove two pairs of connectors that attach to the heating element. Now it's out and you can begin the swap of the new element and reverse this process to put it back together. If I had to do this again, it would take less approx 30 minutes.

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

Girls you can do it on your own!

The easiest way is taking the back off the dryer but if you can't do that just pop the top up and unscrew the front. Just make sure you remember how you take everything out and put it back in the same.

The most difficult part is trying to line up the holes for the heating element, and holding it there while screwing the element in place.

It's a breeze!

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

removing was easy just open lower rear LH panel . Ordering was easy ,shipping seemed like alot? to install the new belt pop top of dryer I used a screw driver to help. remove front panel 2 screws then it also has about six clips may have to have gloves on so you do not skin your hands like I did.... lots of sharp edges. pay attention to the clips, so if they come off they will not be lost. panel will tilt slightly fwd then raise up and set aside. now you can slip the belt over the drum. I kept all the slack at the top till it was in position. the groved rubber side goes against the drum and the motor pully. then extend the spring tensioner into position . I rotated the drum a few times by hand to make sure everything was in position. replace front. check it is lined up well before forceing clips in. check felt material is properly in place, as you rotate it into position. push down top . good to go. I ran it for awhile watching everything work before placing it back in service. you may want to clean it out some while it is apart I used an air compressor and shop vac simultaniously as that seemed to work best. Wanted my son to do it as I think he had it over loaded as to why it broke? It maybe the bearings are going but it felt solid ?? I should find out in a month or so shich was which! I did not see any easy way to get to grease it. The belt was easy though pretty sure my son could have handled it!

Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap

Very easy and straight forward repair.

Unplug the dryer and move it to a location that offers some room to work.

Use flathead screw driver to pop the front side top of the dryer up then lift the top of the dryer up to expose the drum.

Use phillips head screw driver to remove the two screws from the access panel on the rear of the dryer. Reach into the access area and remove the drum belt from the tensioner assembly. It's spring loaded so watch your fingers.

Disconnect the wiring harness at the right front of the dryer.

Remove the two screws that secure the front of the dryer to the sides.

Remove the front panel of the dryer by pulling the panel forward then up and off the two tabs at the bottom.

The felt strips and glides (which are worn off if you are doing this repair) are glued to the front panel of the dryer and now need to be removed. Removing the old felt will take some time and is the most difficult part of this whole repair.

Use some goof off or similar solvent adhesive remover to ease the removal of the felt. A putty knife will likely be helpful too.

Once the felt is off, wipe off any excess solvent and make sure the area to be re-felted is clean and dry.

Apply small serpentine bead of provided adhesive to the felt strips and glue the new strips on to the dryer. There is more than enough glue in the tube provided to get the job done. After applying felt strips, let them sit for about 30 minutes before reassembling dryer. You may want to use some light duty clamps to hold the felt in place while the glue sets but that's probably not necessary since the glue sets rapidly. Follow the directions on the glue tube.

Reassemble in opposite order.

Take the opportunity to vacuum out your dryer and give it a good inspection while you have it cracked open. You just might find those socks that disappeared.

Here are some "while your at it" ideas:

Replace both upper and lower felt strips.
Vacuum out entire dryer cabinet and the foam seal on the air box.
Replace drive belt.
Replace light bulb.
Replace bearing ball on rear of drum or apply some lubricant to the bearing.

I'm not saying do all these things, I'm just suggesting these items as things to consider based on the age and usage of your dryer.

This is an easy one person repair that requires no experience or special tools. Don't pay the repair man. Do it yourself.

I took the repair video in with me and set my lap-top on top of the washer.
My dryer did not match the type on the video exactly (mine has the controls in the front instead of on top and in the back) - however - the parts replacement for the rear drum bearing itself was the same.
After getting the front apart and releasing the drum the rest was pretty easy. Didn't really need instructions for the heating element - that was an obvious change out.
The tips on the video changing the rear drum assembly were very helpful.
Just watch the vid and do it! It took me exactly two hours since I was also changing out the heating element and I did it on a Friday night while having a couple tasty beers.
One tip I would give is the old grease in the bearing is very messy and I got it all over my shirt and pants - and when changing that stuff out don't lean on the front of the frame - I did and bent it out of whack a bit.
The dryer runs like new now that it's done!