GDE336RBS1 Gibson Dryer - Instructions

uncrew old, take out, put new in, screw in place.

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

Lifted broken screen out and replaced it with a new one. Extremely simple.

First I removed power from dryer. Then I lifted the lid and removed the 2 screws holding the front onto the dryer. I then used a pair of pliers to grip the seal and help pull it off. Cleaned off old adhesive. Recommend getting GOOP BE GONE. Then apply high temp sealant onto area and place seal on top. Press firmly across it to make sure it is in place. Then put it all back together and your done. Also, if upper seal is worn.recommend ordering lower seal at same time. I didn't and should have. Save yourself from doing this twice.

Open the top cover by pushing the retention clips in from the front (just under the top edge) with the putty knife - that was the hardest to figure out - I found it online.
The rest is just 4 screws - 2 inside to release the plastic filter holder and two on the inner edges of the front panel.
Took the front off, ripped the old slider, cleaned the glue residue with alcohol and mineral spirits and a lot of scrubbing, vacuumed all the lint from the fan.
Then glued the new slider in place and clamped it together. Didnt know how long the glue takes so I left it overnight, just in case.
It works well now. Cleaning the ducts and the fan with the vacuum hose made a world of an efficiency difference. They should make an easy way to do this for regular maintenance!

Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.

First I removed the 2 screws on the back. These 2 screws hold the top cover. I also used a flat screw driver to press the 2 locks that hold the top cover, they are located in front and under the top cover . Then I removed the 2 screws that hold the front cover. After removing the front cover I replaced the drum glider and the seal-basket lower. Now my dryer is working perfectly...

I First pulled the top panel up and off from the front. Then, on the inside, removed a square head screw from each side holding the front door panel on. I then pulled off the front panel enough to expose the drum. I then removed the old drum glide with a putty knife, and following instructions supplied with the new glide, glued the new glide into place. I then assembled in reverse order of disassembly.

There was a gap between the drum and the front opening. So, we opened the top of the dryer using the putty knife. There are two clips once you find them you just have to push back on them to release the top of the dryer. Then there are two screws that hold the front of the dryer on. Once they are removed the front of the dryer just came off. The kit has glue and instructions past that point and I just followed them.

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!

As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.

The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.

Once I figured that part out, it was a piece of cake.

Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)

First of all, I LOVE Partselect.com.. The parts are reasonable, and arrive in a timely fashion.. The repair stories are far and away, one of the BEST features of this website - so hats off to the DIY'ers who have helped me overcome my challenges and helped me stay in the ..ahem.. "favorable" graces of my wife.. I need all the help I can get there.. Anyway, read the other repair stories first - LOTS of great insight.. I only have a couple pointers to add - below...

This is easily my 4th appliance repair project with Partselect.com, and I can say without a doubt that the experience has been positive every single time.. Until now.. I got the dryer torn down and realized that I SHOULD have ordered the SEAL-BASKET LOWER felt with my original order. When I inspected it for my list of parts to order, the upper glide was thrashed - no brainer.. I thought the lower felt was fine.. d'oh! I discovered this morning that I was wrong.. So, I JUST ordered the lower basket seal for *next* weekend.. (If you are gonna replace the original upper glide, replace the lower basket seal as well..) It'll be a slam dunk, though..

Now, for a couple useful tips:

If you are a car guy, get out your trusty can of brake parts cleaner to help clean off the old adhesive residue after you rip off the old upper glide felt. I also used a 1" plastic scraper to help facilitate removal, but the brake parts cleaner was a Godsend. I think I read someone else's suggestion to use "goof off" or whatever - but I couldn't find mine, so..... ...out came the brake cleaner... :) two thumbs up. Just use it sparingly - all those solvents are bad for children in California for some odd reason..

Spring loaded clamps to hold the felt down as the glue dries are also "nice to have". I used one on each end of the felt, and one for each of the teflon / plastic glides..

Finally - milk this job for all it's worth - it'll only take you 45-60 minutes or so... good luck...!!!

1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.