DCCB330ED2WC General Electric Dryer - Instructions

started with replacing the belt and tension pulley which I purchased from another source. I found your videos on line and they are great. easy to follow. Realized I needed the bottom vent assembly and your prices were better than my local supplier. It was easy to replace thanks to your video. It was nice that you included it in the final order status. The only problems. Did not know the duct felt seal was included with the new duct assembly. I ordered the wrong bearing slides, web site showed both green and white for my model. I now realize I should replace the upper bearing housing. Can I return the unused parts, unopened and have that put as a credit to my next order? Thanks

Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.

Hand replace

Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)

just replaced the unit handle and how my wife can open the dryer without a screwdriver

I pulled the old handle off and pushed the new one on.
No problem at all.

Snap off and then snap New one on.

was no repair- removed filter from door and installed new filter into door. No tools required.

My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.

removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.

Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.

Exactly how your perfect video instructions showed me. Thank you for a job well done!

Watched the video on a different style of dryer so taking apart a bit of a challenge. The old Front Drum Bearing was completely gone on left side and a challenge to pry it off the front dryer panel. replaced felt seal and front drum bearing. noticed that there was 4 places for new bearing slides. the ones i ordered were white and green but did not know why or which one went where as no explanation with packaging. also only ordered one of each and so now had to stop and try and find two more. ! hour later i had brought back a tupperware lid that was thick enough and stated could go to 194 degrees F. i cut out one replacement for green bearing and reused the old white one since it was in good shape from right side of drum bearing. i went back to this website and noticed in the comments section for drum bearing that someone stated the green bearing slides go in at positions 11 and 1 and the white at 10 and 2. they are different materials and having more weight of drum on green now made sense. put machine back together and told neice to keep eyes and ears on dryer thru cycle. she did not even know it was running just in next room.

Unplugged dryer, slid away from wall, and rotated 90 degrees. I removed top panel, and front panel, pulling off 2 electrical wires, and disconnecting 1 Molex connector, for the door switch. I turned the front panel around, and leaned up against the dryer drum. I removed the light bulb, then snapped off the remains of the upper bearing, then unsnapped the duct panel assembly. I carefully positioned the duct assembly against the front panel, carefully making sure not to pinch any wires, and pressed into place. I then pushed the bottom of the top bearing into the duct assembly, and pushed the top into place, replacing the bearing wear strips, 2 black, 2 white once bearing is snapped into place. I rewired the door switch, put the bulb back in, screwed the front panel, then top panel back on, rotated back into position, plugged it in, and started dryer. Problem solved!

Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.