DDC4580BBL General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barry from Dunellen, NJ
- Parts Used:
- WE12X81
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Broken Belt
First unscrew the two screws at top to disconnect the control panel. Lay unit on the back. Remove door(be careful not to lose washers and hinges). Remove four screws to lift off top. Wiggle drum, slip belt over drum. Replace door, then put Four screws back in place.Stand unit upright.Remove back panel, you should see belt hanging.Pulley wheel is in front of you.Follow instuctions sent with pulley wheel.Reattach you're ready to roll, make sure you sllip the belt on the drum until the drum spins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Port Saint Lucie, FL
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter broke it was over 10 yrs old
place inside of dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from North Chelmsford, MA
- Parts Used:
- WE4X444
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Gas would not ignite
Replaced gas igniter The part came a day after I ordered it. I really liked the speed of delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Tranquility, NJ
- Parts Used:
- WE12X10014, WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
dryer not running
drive belt gone, replaced belt and bearing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Glenwood, IL
- Parts Used:
- WE25X60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noise when dryer spins
unknown
25 year old GE dryer started making strange scraping noises when running. This even when there were no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.
Kevin J. Reynolds.
25 year old GE dryer started making strange scraping noises when running. This even when there were no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.
Kevin J. Reynolds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Penn Valley, CA
- Parts Used:
- WE3X75
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Berring was worn out and was squeeking
I opened the top,by removing the two screws inside the door
on the top. then removed the frount by removing the two 5/16 sheet metal screws inside facing the frount. then pulled the drum out and replaced the berring. Cleaned out the lent from the motor and duckings. Then reasembled.
on the top. then removed the frount by removing the two 5/16 sheet metal screws inside facing the frount. then pulled the drum out and replaced the berring. Cleaned out the lent from the motor and duckings. Then reasembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Troy, VA
- Parts Used:
- WE12X10014, WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Has squeek then the drum quit turning
Removed the top, four screws under the front inside the open door. Then the removed the front, two screws inside at top by drum and two screws on bottom. Then pulled out the drum, from there I was able to get to the bearing that was bad. Mine was a older model than the instructions showed that came with my repair parts but it was colse enough to get the job done. Your website is AWESOME!!! The entire experience was wonderful and made my repair as painless as possible. I have already recomended it to my friends, keep up the great work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. from Luverne, AL
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter was tearing up
Easy as steps 1 & 2, remove old filter & replace w/ new.
It fit perfectly which was my main concern, as I could not tell from picture if the length was correct.
I am very pleased w/ product & it works just fine..
It fit perfectly which was my main concern, as I could not tell from picture if the length was correct.
I am very pleased w/ product & it works just fine..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from De Queen, AR
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Filter had developed holes in the filter
Pulled the old filter out of the door of the dryer and then removed the new filter from the shipping box and took the new Lint filter out of the packaging and then slipped the new lint filter into the lint filter holder and started up the dryer and away we went on our happy way. Thanks to all of you guys and gals at PARTS SELECT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leona from Milford, CT
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems
I called customer Servioce and they helped me with the corrfect part number
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Madison, NJ
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The lint filter was ripped in multiple locations
I just replaced the old filter with the new filter and I wonder why I didn't order a replacement filter sooner.
Was this instruction helpful to you?
Thank you for voting!
(Gas) dryer wouldn't heat.
Found and ordered igniter on Tuesday. Part arrived on Friday. Took about 5 minutes to remove old igniter and install new one. Took about 5 minutes. Dryer works like new again. Hopefully it will last for another 16 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Morrisivlle, NC
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter has never been replaced.
This wan't a repair. It was simply a part replacement for a part that was easily accessable. I was more pleased at the fact that I could find the part considering how old the dryer is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from albert lea, MN
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Torn ratty old lint filter
Finding parts for very old appliances (that otherwise are working great!) was very much appreciated...lint filters are very very important and this one has served it's useful life. Thank you for such an amazing parts inventory, good prices, and FAST delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from Little Chute, WI
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wire mesh on the lint filter separated from the frame and lint was getting inside the dryer.
Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1
Was this instruction helpful to you?
Thank you for voting!