DDE8200RAL General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Rochester, NY
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Drum was squeaking and making a lot of noise!
Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from CAMP VERDE, AZ
- Parts Used:
- WE25X60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Squeak when running
Moved the dryer so I had room to work. Took off front of dryer with torx socket. Took off drum belt then able to take out the drum. The glides were worn replaced with two new glides (held in with 5/16 screws). While apart replaced the heater assembly and replacement of the drum belt. Went very well and smooth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from EASTON, CT
- Parts Used:
- WE12X83
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Replace broken drum belt and belt idler pully wheel.
Watched video instruction, paying attention to what it showed in machine. Several virsions of similar designs over the years, look over yours and note access points, take pictures as you go! Just pay attention, it is very logical. Spread the side panels to get the drum in and out, and pay attention to drum axel in back and the bushing it rides in. Be patient, be firm but gentle, no real forcing needed if you are alligned. Be sure the grooves of belt are on the drum, drive wheel on motor, no twists. Reverse order to reassemble. There are several internet videos of models with same basic setup, so look at others if one doesn't show the detail you need to see, or clear some uncertainty. Your local hardware to sorce push fastening for the idler wheel to shaft if you mash it up, they are cheep and several styles will work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Penn Valley, CA
- Parts Used:
- WE3X75
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Berring was worn out and was squeeking
I opened the top,by removing the two screws inside the door
on the top. then removed the frount by removing the two 5/16 sheet metal screws inside facing the frount. then pulled the drum out and replaced the berring. Cleaned out the lent from the motor and duckings. Then reasembled.
on the top. then removed the frount by removing the two 5/16 sheet metal screws inside facing the frount. then pulled the drum out and replaced the berring. Cleaned out the lent from the motor and duckings. Then reasembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Tranquility, NJ
- Parts Used:
- WE12X10014, WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
dryer not running
drive belt gone, replaced belt and bearing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Glenwood, IL
- Parts Used:
- WE25X60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noise when dryer spins
unknown
25 year old GE dryer started making strange scraping noises when running. This even when there were no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.
Kevin J. Reynolds.
25 year old GE dryer started making strange scraping noises when running. This even when there were no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.
Kevin J. Reynolds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Patchogue, NY
- Parts Used:
- WE12X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Belt broke
Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Vista, CA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb blew out inside the dryer
Screwed the light bulb into the socket (duh)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from albert lea, MN
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Torn ratty old lint filter
Finding parts for very old appliances (that otherwise are working great!) was very much appreciated...lint filters are very very important and this one has served it's useful life. Thank you for such an amazing parts inventory, good prices, and FAST delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Morrisivlle, NC
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter has never been replaced.
This wan't a repair. It was simply a part replacement for a part that was easily accessable. I was more pleased at the fact that I could find the part considering how old the dryer is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. from Luverne, AL
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter was tearing up
Easy as steps 1 & 2, remove old filter & replace w/ new.
It fit perfectly which was my main concern, as I could not tell from picture if the length was correct.
I am very pleased w/ product & it works just fine..
It fit perfectly which was my main concern, as I could not tell from picture if the length was correct.
I am very pleased w/ product & it works just fine..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Madison, NJ
- Parts Used:
- WE18X26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The lint filter was ripped in multiple locations
I just replaced the old filter with the new filter and I wonder why I didn't order a replacement filter sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from HILDA, SC
- Parts Used:
- WE4X795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No heat
Long eventful troubleshooting. No success. Read your troubleshooting guide. Showed either high temp. sensor or timer. One person commented go straight to timer. So I did. 2 minuite repair, back in service. Thanks
Was this instruction helpful to you?
Thank you for voting!