DDE3000PH General Electric Dryer - Instructions

I removed the 2 screws and lock assemblies from both sides on the back. Then i removed 4 screws (two from each side) on the control panel and lifted that up as i tipped the cover forward to disconnect the wires from the door switch. I found the wiring diagram inside the control panel cover, which included a belt routing diagram (very helpful, being the belt was laying in the bottom. I then removed 3 torx srews holding the drum to the bearing, and removed the drum. Let the fun begin! i proceded to put the belt onto the motor pulley and around the tensioner. i needed some help from my wife to set the drum back in as i held the belt up around it. once the drum was back in, i found the beld had fallen away from the tensioner. I lifted the front of the drum up just enough to get both arms below it and move the tensioner back to slip the belt over it correctly. With the new belt on i started to put the screws back in the drum. This got very frustrating, as you have to correctly line up all the holes again, while holding the drum in the correct angle to start the screws. this was the hardest part, not physically, but wears on a person's nerves quickly! Once all the screws were in and tight, i took a deep sigh of relief before i tipped the front cover up just enought to get the wires hooked back up for the door. I turned the unit on to verify the repair before re-assembly. Yep! works again, for well under $20.00! Thanks PartSelect!

Found excellent instructions and diagrams online by searching under the model number. Best of all was the service from PartSelect. Belt arrived 24 hours after ordering. It was the right part, it was easy to install, and the dryer is running beautifully.

I searched the web and found a site that explained how the unit came apart. Took it a part almost according to instructions (I thought I saw a short cut that wasn't).
Unplug
Remove top, torx screws above door, tilt top back, lift front (swing to the right).
Remove clip from back of drum, and slide the drum out(watch the belt or remove tension first)
Remove wires and restring
Slide belt on to drum.
Slide drum back into dryer.
Reinstall front and top.
Retension belt.
Plug back in.
I took the time to remove the duct and cleaned out the unit before reassembly.
Also it helps if you can get easy access to all sides of the unit. I could not, the owner had stored stuff around it to the point that it would have added several hours to the repair to gain easy access. So I had to do some gymnastics to get to all the area's to work on the maching. It is my Dad's dryer and that is enough to write a novel about.
If I had followed the above, it would have saved me an hours worth of time.

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

Remove the bottom cover of dryer to look at the motor, see belt hanging remove broken belt. Remove screws from the top and front, slide belt over drum put small piece of tape to hole belt in place replace screws go back to the rear pull belt over the motor pulley close back panel

First I took the lower bottom off the back of the dryer (bolts), pulled the old pulley off the idler and put new one on. Second, I took the screws out in front (under lip of top) and then removed bolts from bottom of the front. Then lifted lid up and swung front to the side. I was then able to take the drum out and clean it before putting it back in with the new belt. The put everything back together.
Dryer ran for ten mintues and then quite again. Seems to be in the motor and not the less expensive parts I found to be worn.

I follow the easy instruction by a user in your web site to reach the problem area and discoverd the drive belt was broken.
As it turned out, the problem was compounded when I discovered also that the Heating element needed replacement.
At this point I decided it was time to let go and got a new dryer, choosing the same brand that lasted 25 years: GE

First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack between the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.

We removed the lid to the dryer. The drum had to come out so the back access was removed and the belt taken off. The drum then slid out the front. The dryer had two elements both were broken. The new ones were stretched to the proper length and laced through the ceramic brackets. The new copper leads werre installed and the coils attached to them. We cleaned the dryer as much as possible and reassembled it. Works like a charm (for now)!

First unscrew the two screws at top to disconnect the control panel. Lay unit on the back. Remove door(be careful not to lose washers and hinges). Remove four screws to lift off top. Wiggle drum, slip belt over drum. Replace door, then put Four screws back in place.Stand unit upright.Remove back panel, you should see belt hanging.Pulley wheel is in front of you.Follow instuctions sent with pulley wheel.Reattach you're ready to roll, make sure you sllip the belt on the drum until the drum spins.

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

First of all unplug the dryer, move it to a location that you have room to work around it. Remove the top and then take the two screws out that are on the inside of the dryer close to the top and then loosen the two bottom front screws only. Remove the front of the dryer and then look in the back of the dryer in the center of it and there is a square hole with a cover, remove the cover and behind it is a c-clamp, remove it. At this time release the tension on the dryer's belt and then pull the drum out towards the front of the dryer. Once this is done you'll be able to see the heater coils. You have to remove the bolts that the wires are attached to and cut the wire so you can pull the old coils through the glass rings to get the old coil out. Open your package and have a 48" yardstick or a tape measure and stretch the coils to the lengths in the instructions. Thread the new coils through the glass holders and then you have to remove the three heater wires that go through the wall of the ring so you can connect the new wires to the new bolts provided with your kit. One idea is to take a picture with your smart phone before you take anything off if it seems you can't remember what when where so you can see how the wires and bolts go back together. Once you have the bolts and wires connected you just reverse the process and put the dryer back together. *********** If I knew what I know now I would order a few of the glass holders because two of mine were burnt and I would have replaced them if I had them; I'd buy 4 to 6 of them to make sure I had enough.

Backwards to start- here's the correct way.Disconnect power and vent hose-tip onto front-remove bottom plate allowing access to bottom of dryer and the belt pulleys-remove the small plate in center and under that is a C-clip holding the drum shaft in place-remove the clip and washer-sit dryer upright - open the door and remove the 4 screws under the upper lip which hold the top of the dryer in place-lift up top and secure or have someone hold it up.-inside the top front on both sides are 2 screws per side and there are 2 screws at the bottom under the kick area, remove all 6 of these screws and the front of the dryer will come off-watch the wires-with the front off you can pull the drum forward to allow installing the new belt. - hold the new belt in place with a couple of pieces of tape-reverse the procedure to put drum back together and then thread the new belt onto the drive pulley and under the idler tension pulley.- reinstall back plate, vent hose, power and you're ready to go have a beer.

Parts arrived within a couple of days,the repair went fairly easy.