DCCB330GD1WC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Poughkeepsie, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Not Starting
First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Poughkeepsie, NY
- Parts Used:
- WE3M26, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer started to thump and scrape
First and most important - safety. Either unplug the dryer or shut off the circuit breaker. Remove the two screws to the top cover. To locate these screws just open the door as they are located at the top of the door opening. Remove screws and lift up the top cover and carefully pull towards you. Place to the side away from the work area. This now will expose two screws within the side panels holding the front door and front housing. Remove the two screws, lift up and out to remove front housing assemble. Be careful when you remove as the wiring to the light fixture is included. Just remove cover and place side ways close to the dryer.
Remove the bulb then remove the white plastic drum bearing (snaps out or in when replacing with a flat screwdriver).
Prior to installing the new drum bearing install the four white slide strips on top of the drum bearing. Review the old parts for comparison. These actually act as the bushings between the drum bearing and the clothes drum. Please keep in mind the slides do not come with the drum bearing when ordering. You must order seperately. Once the new assemble is snapped into the metal front cover/door now you can re-assemble. While you have the drum exposed it's a good time to check the belt for wear. Sometimes a worn or ripped belt can be the same symptom of the thumpimg sound. For the assemble just reverse all the earlier steps. Plug cord back in or turn on the circuit breaker and run the dryer. You should be good to go for more years of service.
Remove the bulb then remove the white plastic drum bearing (snaps out or in when replacing with a flat screwdriver).
Prior to installing the new drum bearing install the four white slide strips on top of the drum bearing. Review the old parts for comparison. These actually act as the bushings between the drum bearing and the clothes drum. Please keep in mind the slides do not come with the drum bearing when ordering. You must order seperately. Once the new assemble is snapped into the metal front cover/door now you can re-assemble. While you have the drum exposed it's a good time to check the belt for wear. Sometimes a worn or ripped belt can be the same symptom of the thumpimg sound. For the assemble just reverse all the earlier steps. Plug cord back in or turn on the circuit breaker and run the dryer. You should be good to go for more years of service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from GALES FERRY, CT
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken piece
Snap out the broken part. Snap in the new part. Use caution with the wires, but don’t have to disconnect them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from WARRIOR, AL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased a used dryer & lint filter had holes due to rust
On my GE Dryer the lint filter is located inside the door at the bottom. The filter can just be pulled out by hand & a new one pushed into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Wake Forest, NC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old screen was not sealing properly
Replaced new screen in place of old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from DOVER, AR
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from INMAN, SC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from HAWLEY, PA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke
Snap off and then snap New one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- syd from wilmington, NC
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no handle
just replaced the unit handle and how my wife can open the dryer without a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John C. from Cincinnati, OH
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door handle was comming off had broken hook
I pulled the old handle off and pushed the new one on.
No problem at all.
No problem at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor from ST AUGUSTINE, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
door filter
was no repair- removed filter from door and installed new filter into door. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from EDGEWATER, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
take the old dryer lint screen out
Hand replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from EDGEWATER, FL
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My last phase of repairs of minor items.
if your unit has over 6,000 hours of operations, one needs to remove the front panel and inspect the sliders that the drum rides on. The video were very helpful to replace the sliders. Unfortunately, my dryer had over 10,000 hours of operations over a 30 years period, hence a major repair costing over $200.00 dollars. The drum sliders were gone, hence the drum eat through the plastic guides. More so, the drum started to eat away the front panel. If the dryer is eating your closes and making a noise, one is looking at a $200.00 repair job. Hence check the sliders early will save one $$$$.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from BELFORD, NJ
- Parts Used:
- WE4M415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Switch not working.
Open the door and removed the part. Installed the new part and started the dryer.
Was this instruction helpful to you?
Thank you for voting!