VD512FG*429 General Electric Dryer - Instructions

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.

I only ordered a lint filter with frame but wanted to let other's know that ordering from your site was extremely easy and the shipping was extremely fast!! I received my order with 2 days of placing my order. Thank you!!

Deftly removed the old lint trap and placed the new frame in place. It worked perfectly. Hands only repair.

inserted the latch into the opening in the front face of the dryer

place new filter in

no instructions necessary for this part install

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

the replacement part was easy to replace but remembering how the belt went back on took alittle more time..

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

I watched video supplied from parts select, only took about 30 minutes, hardest part was putting belt back on, couldn't fit hands in easily, but once I did it, dryer is like new, can't hear a thing.

I was unsure of how to disassemble the machine to reach the belt, but a YouTube video gave me confidence. Thanks to Partselect.com, the great customer service, and fast delivery. I had my dryer up and running really fast! The process was really not difficult at all and it gave me a chance to vacuum out years of trapped lint. I am so happy to have saved hundreds of dollars, not having to buy a new dryer.I would urge other folks to tackle these relatively simple repairs, the right parts are a phone call away. Frank

sort of followed instructions, would have beenhelpfull if they told me I HAD TO REACH INTO THE MOUTH OF A SABRE TOOTHED TIGER to install the new belt.

Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.

The job is simple once you know how to remove the front panel. The steps are as follows:
1. disconnect the power cord.
2. remove 4 Phillips-head screws under the lip of the front panel that secure it to the top panel (#1 point Phillips-head screw driver)
3. swing the top panel up, it is hinged in the rear.
4. making note of the connection points of the color-coded wires, disconnect the wires to the lamp socket and door switch (I used a felt-tipped pen on the inside of the front panel to mark the connection points, "R" for red, etc.)
5. remove the upper 2 hex-head screws from inside of the front panel (5/16" nut-driver)
6. loosen the lower 2 hex-head screws (5/16" nut-driver) accessible from outside the panel (you only have to loosen them since the bottom mounting tabs are slotted)
7. slightly lift (to clear above mentioned lower tabs) and tilt the front panel toward you. Swing the front panel to the right as though you were opening a door and position so it does not fall.
8. remove 10 hex-head screws from the black lower rear access panel (5/16" nut-driver) and remove the broken drive belt. Note that the narrow black panel securing the power cable can remain in place.
9. at this point take advantage of the situation and vacuum out the years of lint and dust you could not reach before.
10. stand in front of the dryer, lift the dryer drum slightly and slip the new belt (rib side down) around the drum. Position the belt near the rear of the drum along the wear-mark left by the old belt.
11. go to the back and place the belt in the motor's drive-belt pulley, making sure the ribbed side of the belt mates with the ribs in the pulley.
12. position the tension wheel so that the it takes up the slack in the drive belt. Note the flat side of the drive belt will mate with the flat of the tension wheel.
13. spin the dryer drum a few turns by hand to make sure the drive belt lines up properly with the pulley.
14. reassemble the dryer by reversing the above steps, starting at step 8.