HDL607SW418 General Electric Dryer - Instructions

drive belt gone, replaced belt and bearing

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

After removing pieces that were stuck in the door, I simply popped the new handle in place. It took less than a minute. What was the easiest was ordering and receiving the new parts- I ordered and 2 days later I received the new parts. I didn't expect to get the new parts for at least a week.

inserted on an angle and snapped in place.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.

Long eventful troubleshooting. No success. Read your troubleshooting guide. Showed either high temp. sensor or timer. One person commented go straight to timer. So I did. 2 minuite repair, back in service. Thanks

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

replaced rear drum bearing kit Still makes the same noise

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

Removed the top, front and lower rear section of the dryer. This being my first experience replacing a dryer belt I naturally missed the tensioner pulley first try, then installed the belt on the wrong side of the pulley and found I didn't have enough tension. After some thought and a long hard look I realized my mistake and the third time was the charm. Next time I need to replace a dryer belt it should be a snap and go a lot faster.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.

I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.

I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.

First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).