PDVH515EF1WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from Freeland, MI
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
loud noise when ran for 5 min.
Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Dassel, MN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Dryer squeaked when running
Took the dryer apart to get to the rear bearing. Took the bearing assembly out, kept the e-ring from the old bearing shaft, replaced the bearing kit, took the o-ring off the new shaft and replaced it with the e-ring, then reassembled the unit. Make sure to place a nail or long screw into into the rear of the drum, so that you can realign bearing on the drum. It is easier with two people when reassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell P. from Dushore, PA
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Noisy Bearing "SWEEKING"
The first thing I did was move the dryer out so I could "unplug it" !
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Naples, FL
- Parts Used:
- WE11M23
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Low heat
I bought the Heating Element and Housing together so that I would not have to stretch and run the coils and to save time!
1. I removed the two screws that hold the top down by opening the dryer door and removing the two screws at the top of the door opening. Then I pulled the top off.
2. Then I removed the two screws on the top inside of the dryer on the left right and took the front off.
3. Next I spread the dryer open a little and pulled the drum out while pushing the belt off the back of the drum.
4. Then I removed the screws to the sensors and removed them from the housing.
5. Then I removed the four screws holding the heating element housing to the back of the dryer and took it out and put in the new peace.
6. Do everything in reverse when putting the dryer back together.
1. I removed the two screws that hold the top down by opening the dryer door and removing the two screws at the top of the door opening. Then I pulled the top off.
2. Then I removed the two screws on the top inside of the dryer on the left right and took the front off.
3. Next I spread the dryer open a little and pulled the drum out while pushing the belt off the back of the drum.
4. Then I removed the screws to the sensors and removed them from the housing.
5. Then I removed the four screws holding the heating element housing to the back of the dryer and took it out and put in the new peace.
6. Do everything in reverse when putting the dryer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laurel Springs, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from FARMINGTON, ME
- Parts Used:
- WE05X20431, WE09X27634, WE03X37317, WE14M124, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The felt seal came out, and drum slides were cracked
We watched the YouTUbe video of Steve from this site and followed his instructions for how to replace the top bearing on the dryer, and the seal. It went quickly and easily, and his instructions were perfect. It helped that the model in the video matched ours almost exactly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuc from WOODBRIDGE, VA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from EPHRATA, PA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from OLD TOWN, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher
Replace both micro switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from CORP CHRISTI, TX
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from BELFORD, NJ
- Parts Used:
- WE4M415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Switch not working.
Open the door and removed the part. Installed the new part and started the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from CEDAR RAPIDS, IA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out
Unscrewed the old bulb using the lefty loosey method. Installed the new bulb by turning it clockwise or righty tighty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Los Gatos, CA
- Parts Used:
- WE05X20431, WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Constant Squeeeeeks!
Piece of cake, mostly because of the nice exploded drawing that was on the site when ordering the parts, it was easy to identify what was needed and order it.
I will never call a repair man again :-)
I will never call a repair man again :-)
Was this instruction helpful to you?
Thank you for voting!