64190419 General Electric Dryer - Instructions

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

Easy as 1-2-3. I took off the top hinge screws in order to lift up the top of the dryer.

I then took off the front dryer piece with the door intact. The lint filter was in the front door section.

I released the wiring clips to the front of the dryer and lowered the front of the dryer down gently. there is enough slack with the wiring if you disconnect the wirre clips.

I removed the old broken belt. ThenI gently lifted thr dryer drum enough to slid in the new belt with the ridges down. Look for the old belt line (worn area on the drum) and slip the belt up on the drum to that point.

Then I replaced the wiring with clips and put the front of the dryer back together.

Going around to the lower back of the dryer, I unscrewed the back plate where the exhaust comes out. It was 8 screws with a socket.

Once the back was off, I pulled the dryer pully to the right and fed the reamider of the belt through both pulleys ensuring that the ridged side was on the correct side of the pulley. The pylleys match the ridges on the belt. I rleased the tension on the movavle pulley and it was done.

All I had to do was button the back up and do a "dry run" I quick have the drum a half roation from inside the drum with the door open. Then it was all gravy. I was done and saved myself a good deal of money. Look on the net for pics to make thing easier for you. There are people out ther who will NOT charge you for this info.

First i removed the lower rear inspection plate to see what the problem was.
next i removed the screws in the front top panel.
next i lift the top back,the rear hinges held it in place.
next i removed the bolts that held the front panel in place,but before i removed the panel i removed the wires that were connected to the front elements and disconnected then,
next i removed the front panel,then i place the new dryer belt over the dryer drum,but first you have to rise the drum up a little to get the belt under it.
next i put all the front panels back in place,make sure you reconnect the wires that you removed earlier.
next i moved to the back panel, there i position the belt over the dryer drum,then i place the belt over the motor drive pulley, then i pull down the tension bar roller to the left and place the belt over it.Then i replace the rear panel in place.plug in the power core and turn it on. finished. After over 35 years this is the first time i had to replace the belt,matter of fact this is the first time i had to replace anything on this dryer, washers will that is a different story. but the dryer runs great maybe for another 30 +years LOL.

Removed the rear access panel (8 - 10 bolts), checked the pullys. Opened the dryer door, removed 4 allen screws at top and lifted the top of the dryer (like a hood on a car). Removed a screw (phillips) on each side (inside) pulled open the front and worked the belt around the drum. Placed belt onto pullys, plugged in checked for proper rotation of drum then unplugged and installed screws and bolts. - Fairly easy, saved a bunch from a service call. I also found 15+ years of lint inside the dryer. Vacumed and cleaned the inside -it even dries faster! Sorry Honey - No new dryer this year - Now can I go hunting?

snapped in new latch

watched the video on your website,this made repair to the dryer very easy.hardest step in the repair was getting the belt hooked up on motor and tensioner,but being old and persistent i finally won!

Replacing the bearing and belt on a GE DDE6350BBL dryer

My belt broke and landed up in the bottom of the case, therefore no problem removing it.
Having to replace the belt I decided to renew the bearing at the same time.
Detailed instructions, with comments follow for those of you attempting this repair.
Most important, READ ALL THE INSTRUCTIONS BEFORE STARTING WORK
Take careful note as you take things apart of what they looked like before you started.

First unplug the appliance. Always unplug the appliance before doing any repair.
With the appliance stood in a space where it is accessible all round begin.
Open the front door and remove the small Phillips screws located at the top of the front panel.
( You have to look upwards to see them, normally four screws )
The cabinet top can now be lifted carefully upwards. It is a good idea to use a piece of
2 x 4 to hold this in a raised position for the time being.
Inside the cabinet on the right at the top, behind the door open switch, remove the two electrical slide connectors from the switch.
Remove the hex headed screws securing the bottom kicking plate, ( four screws )
Remove the two longer hex screws securing the bottom of the front panel, ( two screws )
Look inside the cabinet, each side towards the top there is one hex headed screw securing the top of the front panel to the sides ( two screws )
Hint head of screw faces back of cabinet.
The front panel can now be removed by lifting slightly up and away from the rest of the case. Do not try to move it too far, just turn it through ninety degrees and lean it against something heavy. Hopefully placed there to lean it on before you started.
Using a torx screw bit, remove the three torx screws securing the drum onto the bearing.
( A noise will be heard like something dropping, we will take care of this later.)
Lift the drum out of the case and set it aside.
Using a Phillips screwdriver remove the four screws securing the bearing to the casing.
Lift out the complete old bearing assembly.
Now is the time to thoroughly clean all the parts, before reassembly.
A Hoover with a crevice tool is good for removing most of the lint in and around the case. In severe cases it might be necessary to use a wire brush to loosen the lint.
Look in the bottom of the case and find the spacer, which fell off when you removed the drum. It is circular with a large hole in the centre and six holes around the side.
It is a good idea if you are adventurous, to remove the slide connectors for the heater elements and remove this assembly for cleaning. If you are not adventurous then cleaning it while installed is possible but be careful of the wire spirals, they are fragile

Helpful hint.
At this point take one of the old screws, which secured the bearing into the house.
Take this screw to a good hardware store and ask for two extra screws three inches long with the same thread. Make certain the thread is the same. Bring your new screws home, put them in a vice and saw off the heads, thus leaving two pieces of threaded rod three inches long of the correct thread. Doing this will save you a lot of aggravation later.

To replace the bearing, assemble the new bearing with a small quantity of high heat grease applied to the bearing surfaces. The old circlip can be reused without problem as long as it was not damaged when removing it.

Hint the new bearing is supplied with an 'o' ring in the groove where the circlip goes, this 'o' ring has to be removed before assembly.

If you have removed the heater assembly for cleaning it should be reinstalled now.
Install the new bearing in the casing using the four new screws provided.
Carefully screw your two threaded rods into two of the three holes in the bearing surface.
Locate the spacer plate onto the threaded rods and slide back until it is in the correct position.
Hint, it will only go on one way round, with all the holes lining up correctly.
Place the new belt loosely around the drum before it is installed in

Open the dryer door and remove the two screws in the top of the door opening that hold the top of the dryer on, and then remove the dryer top. On the inside of the dryer, there are two screws that hold the front of the dryer on. Remove one screw from each side of the dryer near the top, and the front of the dryer will fall away. The drum slides are visible when you lean the front panel of the dryer out away from the drum. You can replace the drum slides without even removing the front of the dryer completely. Pull out the old drum slides and insert the new slides. Lift the drum slighly from the inside through the dryer door as you tilt the front back into place. Reinsert the screws holding the front of the dryer on and tighten. BE CAREFUL not to drop the screws or you may have to disassemble the dryer to get at the dropped screws. Reinstall the top of the dryer. It is a difficult fit which requres inserting into 3 tabs and sliding the top into place. Check that the top is flush before inserting and tightening the screws in the top of the door opening.

I unscrewed the two screws that are on top of the timer panel either side. and the two screws that are under the timer panel both sides. The whole assembly will come apart and expose the timer. Unscrew the timer (three nutdriver type screws). Unplug the wires (make a map of what color wire goes on what terminal before you unplug them. I had a wire that melted and burnt on to the terminal. I had to strip and crimp a new terminal onto thr wire. The new terminal is a common one found in hardware store. There is a front panel and the back panel that the Timer knob has to fit between. I forgot the knob and had to take it apart the panel assembly again to get the knob between the front panel and back panel. It is pretty straight forward and easy, once you get the courage to tear the thing apart. Just reassemble it the same way. Oh my dryer is old I used WD 40 on the terminals to get them loose. The replacement part was exactly like my old one. I was worried it would be different but I was pleasantly surprized it was a perfect replacement part.

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought