PVXR333GTOWW General Electric Dryer - Instructions

The repair was done as follows:

1. Removed the door
2. Removed the two screws securing the top panel then removed the panel.
3. Removed the two screws securing the front panel then removed the panel.
4. Removed the screws securing the left side panel then removed side panel and the two leveling feet.
5. Tipped dryer over on its back (you will want to protect your floor, the four screws that attach the heater unit protrude through the back).
6. Disengaged the belt tensioner and removed the belt and the drum.
7. Removed the three Torx screws securing the drum bearing to the drum and discarded old bearing.
8. Removed the four screws securing the bearing retainer to the heater unit.
9. Removed the four screws securing the heater unit and two sensor wires.
10. Lifted heater unit just high enough to remove bearing retainer. Discarded bearing retainer.

The new drum bearing kit is supplied with self tapping screws. I installed the screws into the bearing parts to tap the holes and then removed them prior to assembly.

11. Installed new bearing retainer to back of heater unit using the supplied screws. Install the four screws by hand, finger tight.
12. Re-attached heater unit and tighten screws.
13. Re-attached sensor wires.
14. Tightened the four bearing retainer screws.
15. Attached new drum bearing to drum using the three supplied Torx screws. I used tape to hold everything together while installing the screws.
Tightened the Torxscrews.

Next I used a vacuum to remove all the lint from inside the dryer. I also used a small plastic putty knife to remove the caked on lint on the impeller blades.

16. Inserted drum bearing into bearing retainer.
17. Installed drum belt and belt tensioner.
18. Installed left side panel and feet.
19. Replaced the two grey and two white slide bearings on the front panel. They just slip onto a small post and slide into a slot.
20. Installed front panel. (Rotate drum to help with installation)
21. Installed top panel and door

PROBLEM SOLVED!

pulled out door striker anddoor latch out with pliers and just pushed in new parts. works like new in under a min.

I had to take most of the dryer apart because there is no rear access to the motor. It turned out to be easy to dissasembel the dryer. The only problem that I had was that I could not figure out how to route the belt around the motor and the idol pullies. I could not find anywhere that gave instructions on how to properly tension the belt. I finally figured out that the idoler pulley needs to be locked in place on the right side of the engie mount. Then the belt needs to be routed over idoler pulley and under the motor pulley. Finally release the idoler pully from the locked postion to put tension on the belt. It really turned out to be pretty easy.

First I unplugged the dryer and turned off the gas

Second I opened the door and unscrewed the two screws that go up into the top panel and hold it in place (you will need to get down and look under the top of the door jam to see the screws).

Third I lifted the front of the top enough to remove the two screws holding the front panel on (Use a magnetic screwdriver if you have one you do not want to lose the screws taking them out or putting them back in)

Fourth positioned a chair to lean front panel against so it would not fall over or strain the electrical wires that run to the switch in the door (slide the front panel off slowly supporting the drum with your hand so it doe not drop hard on the motor wires or burners)

Sixth determined the parts I needed and ordered parts from pars select and got them in two days

Seventh when new parts arrived I unclipped the old DRUM BEARING removed the felt gasket, put the felt in the new Drum bearing and clipped it in place

Eighth clipped in the 2 new Dryer Drum Slides and 2new SLIDE WH slides

Ninth Vacuumed out dryer and vent pipe completely

Tenth reassembled dryer being careful to make sure drum was properly aligned as I put the front panel in place and the belt was in the proper place on drum and all the screws were back in place.

Ninth turned gas back on and plugged in dryer

Ten turned on dryer to test squeak was gone

Hints as soon as you hear a squeak look into it and you will probably not have to replace the DRUM BEARING. But if any of the Slides are bad replace them all. Check your belt and felt gaskets to see if they are in good shape. If everything up front is in good shape and it is not the motor squeaking it could be the back drum bearing. Take your time keep your old dryer running for a few more years and save the $40 dollar service call. Do not forget to clean out all the old lint and dust out of your dryer and vent pipes not only will you reduce the risk of fire you will be allowing air to pass through the dryer more easily drying your clothes in shorter time.

One of the easiest repair jobs I've ever done. First I turned off the power. After removing 4 screws and lowering the cover of the control board, I disconnected the two wires attached to the switch. I rotated the switch counterclockwise and removed it. Just reverse this process and I was done. I was in and out in less than 10 minutes.

Easy repair. Removed top of dryer and removed two screws to front panel and door assembly. Old front air duct assembly was worn and broken, so it literally fell off the panel. I cleaned the front panel and door assembly of all the lint and dirt, and snapped the new parts into place. The new parts came with the gasket and felt drum seal already installed, to all that had to be done was to snap it into place. Installing the drum slides was a breeze. I simply had to slide one end in the slot, position the hole over the pin, and slide the other end in. I put everything back together, and ran a full cycle for test. Dryer works like new, and run quiet.

Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a snap.

I ordered parts based off other peoples findings. I took the top and front off the dryer. I found the drum bearing(really only a plastic bracket. The slide were completely worn and the drum was wearing into the plastic drum bearing. I popped the old drum bearing out and put the new on in. There are actually 2 sets of slides (4 total). I only bought 2. I reused two of the existing slides. I put the unit back together and it was a lot quieter. I need to order more of the slides. They are only a couple dollars a piece and take most of the beating. I should've but didn't get the pasking or gasket. It was broken. I think it'll be fine though.

I removed the two screws that hold the front panel to the top panel. I removed two more screws that hold the front panel to the side panels. I separated the front panel from the side panels and removed the drum.

I could see on the front panel the drum slides were badly worn. One was gone.

The new parts installed easily using no tools at all. Everything snaps in place. The new foam gaskets press and stick to seal the duct work. The felt strip pressed into place.

I replace all the panels in reverse order and plug it in. It operates fine, but the motor is making the noise. I will look into replacing the motor next.

Removed the top of dryer two screws behind door at top then removed top two screws top corner lift dryer tub put belt around the tub then looped belt around the pullies.

ordered part on line--received in mail 2 days later--
just pushed on in 2 seconds--job done

how much easier can it get??????

Removed top cover of dryer with screwdiver 2 screws, removed front cover 2 small bolts with 5/16 scoket. Removed coil brackets with shor screwdriver replace coils as ness. and put covers back on and works great!

Vinny

The weight of the front section of the drum in the dryer rides on 4 slim pieces of plastic. remove the screws that hold down the top of the dryer are in the front door at the top at each corner. remove the top, then remove 2 screws that hold down the front of the control panel to the cabinet at the base. remove the 2 screws at the of the front corners of the cabinet to separate the front door section from the rest of the dryer.Watch out for the wires the connect the door to the rest of the dryer. if you replace the bearing at the back of the dryer you need to take two screws out at the base of the cabinet one from each corner to let the sides of the cabinet to spread out and let the drum pass though the front of the dryer cabinet. the belt has to come off the motor by lifting it up an sticking your hand in under the drum and working it off the end of the motor. replaced the parts ad the dryer works like new.

1 Unplug power cord. 2 Remove top and front panels. 3 Remove old bearing, slides and bulb. 4 Install new bearing slides and bulb. Reinstall front and top panels. 5 Restore power and test. Time to repair 25 minutes. Very satisfied with the parts and the time to receive them, very good parts service. Will definately use this service in the future and will highly recommend this company.

Doing some simple troubleshooting with the volt-ohm meter I determined that the door switch was failed.

The replacement door switch restored the motor circuit keeping my dryer in action.