677512 General Electric Dryer - Instructions

Remove front by removing two screws at top of door opening. Remove front of dryer carefully becsuse of electrical connections for door switch. Drum sliders simply silde in slots at top. (4 are required for total replacement) Door seal simply fits in the groove and locks over end tab. NOTE Do not run dryer any more than absolutelty nessary without lower seal in place.

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

I followed some simple instructions from GE. It was really easy and I even found some spare change inside the cabinet which my wife took off my hands. :/

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

Took apart by removing the top and front panel. Found drum rubbing due to worn glides and felt.

Replaced the rear drum bearing, Front drum bearing,front bearing tabs and belt. I replaced the belt from the front of dryer. Better to go thru the back. Much easier.

UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.

The video on the site is easy to understand and a snap to follow.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

Took back off control,panel. Took the timer out from the back, but left all the wires on. Took one wire off at a time and installed that wire on the same terminal on the new timer and did the same for all wires, one at a time. Replaced timer. Tried timer. It worked great. Buttoned up back and pushed dryer back in place.