66050439 General Electric Dryer - Instructions

disassembled chassis of dryer, unbolted top, lifted top to expose drum. bolted top back on. resumed repair next morning. unbolted top. lifted drum (it moved up and down about 1 inch) and got new belt around it. rebolted top down. tipped dryer to its back. unbolted and removed panel at bottom, exposing drive motor and tensioner spring. positioned belt around drive motor spindle and tensioner spring. replaced panel. reconnected dryer to electricity. reconnected gas using new flexible connector.

Deftly removed the old lint trap and placed the new frame in place. It worked perfectly. Hands only repair.

inserted the latch into the opening in the front face of the dryer

Break up the broken knob easily with plyers.Once thats off then push on the new knob with your fingers that took 3 seconds ,fit perfect.

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.

place new filter in

no instructions necessary for this part install

After having a friend who repairs appliances come and diagnose the problem, I was able to find the parts I needed very easily at PartSelect. They came quickly and I removed the front panel, followed the instructions (they were not very detailed) and also had help reading some of the other posts from people on the website. I replaced the parts and the dryer is now quiet and running fine.

I did not have an actual repair. I simply replaced the lint filter that dropped into the receptacle. However, what I want to mention is that the part was available as old as the dryer is and there was a nice photo to scale of the replacement part so that I was sure I was getting the correct piece. A great site to obtain parts from my experience.

Just replaced it with the new one

What to do if you have a load of wet laundry at 23:00, the dryer won’t start, and you have no spare start switch.
Removed rear access panel and discovered the wire from terminal #2 (goes to heater coils) on the start switch had melted and disconnected. The start switch showed signs of overheating but not melted. Removed the switch and found the switch’s actuator button was jammed in the ‘in’ position (dryer won't start). The switch was a friendly one in that it was possible to disassemble it. Most switches today are molded/glued together, but this one could be pried apart. The contacts inside were still in fair condition and, after dressing them, the switch was reassembled. The actuator button had a burr that was filed off and the switch action worked fine. All of the 1/4" male QC contacts on the switch were cleaned with a wire brush. The burned wire was cut back about 6” and a new piece of 14ga wire was spliced in with a wire nut. A new 1/4” QC terminal was crimped to the wire and all wires were re-attached to the switch.
This fix would probably last for a long time to come, but I bought a new switch and installed it and will keep the old switch as a backup.
p.s. The load of laundry was dry by 02:00.

Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.

The repair went very well, thanks to this site. Dixie

Remove the Torx screws along the front top edge and flipped the top back. Removed two screws at the top inside holding the front panel on. Loosened two screws at the front bottom and took the front panel off. Pulled the drum out the front. I gave everything a good vacuuming with a shop vac and a long handle brush. Then went around back, removed the access panel, removed the rear drum bearing plate and installed the new one. Removed the rear bearing from the back of the drum and installed the new one (You have to work from both sides of the drum which makes it a little tricky.I used a couple of wire ties to hold everything in place while I lined everything up. Screws or punches would work too). The front drum slides are held in by 2 screws each and you could replace them without removing the drum. They need to be lubed with the lubricant supplied. I put the drum partially in then looped the belt over the narrow back part of the drum, around the motor pulley and idler pulley. Put the drum all the way in and the belt onto the drum by rotating it by hand. The belt ribs go against the drum. Installing the belt was the a little tricky but not impossible. It could be easier if you loosen the left side panel to give you some room to reach in but I was able to do it without doing that. Threw the front and top back on and was done. Total time was about 1.5 hours a lot of which was spent getting the dryer in and out of the little cubby hole it lives it.

I unplugged the dryer and moved it into a open spot on the floor.I then opened the door so I could release the top panel,and tilted it back.This allows the removal of the front of the unit. Folled the instuction for removing the drum and got it out. Cleaned up the area and removed the screws that held the drum to the bearing, and pulled the drum out. The instructions for removing the plate and the bearing where o.k., and the tips given for reassembly were helpful, but would have been easier to see if the were a seperate line. The parts fit GREAT, and this 1989 dryer is ready for a few more years.A good price on the parts and a quick ship.I will shop here again!