PSKP333EB4WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynne from Dewitt, IA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer knob, plastic broke, could not turn on.
pulled old one off, pushed new one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Winchester, KY
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob came off
I'm not experience to repair anything so I put the laptop on top of the washer and watch the video and it was easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Pottsville, PA
- Parts Used:
- WE12X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
idler pulley broken
Pop off the old, pop on the new. I did it with one hand, the 'hard' part was putting the access panal back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Summerdale, PA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would run for 4 minutes and shut off. keep turning it on
Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Cumming, GA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer makes noise when "Start" is pushed, but stops when you let go.
Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from ST. MARTINVILLE, LA
- Parts Used:
- WE12X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer was making a vibrating sound near the bottom left rear area.
I suspected the idler pulley shaft was worn. I found the repalcement pulley on parts select web site. finding the part was very easy and delivery was very quick. After removing the dryer from the wall,I removed the access panel in the rear which exposed the motor, belt, and pulley. After removing the belt from the pulley, I removed the pully assembly from the dryer. I removed the keeper retaining ring on the pulley and installed the new pulley with the new parts supplied. The new pulley assembly was then ready for re-installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Richmond, VA
- Parts Used:
- WE4M415
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer would not turn on
It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.
Was this instruction helpful to you?
Thank you for voting!