HDA637MW429 General Electric Dryer - Instructions

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

Unplugged machine and turned off the gas. Removed top panel,4 screws along inside top edge of door opening. Used a wooden shim to pry the drum away from the surrounding "lip with felt padding. Slipped belt through.the trick is getting the belto around the entire drum. First I got it over the top of the drum, and fed it around the bottom by turning the drum and pushing the belt through the opening made by the shim between the bottom of drum and the lip with felt. It was kind of like feeding a bicycle chain onto a sprocket as you turn the wheel..
Removed back panel and vent hose, removed old belt laying on floor of machine, fed the belt onto the motor pulley and the tension pulley. Tension pulley presses on top side of belt. Belt should be in same position on drum as old belt, you can see a friction mark all around the drum from the old belt.
Replaced panels and vent hose. Put felt padding back into place wherever it slipped out. Very important because if you don't it scrapes the drum when turned on and makes a loud sound.
Dryer works perfectly again.

Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

it was easy, it clip right on.needed to give it a little tap to get it in .

Just like the other stories, remove the top and front of the dryer, replace the bearing and slides (or slides only if needed). I ordered only the slides, but also needed the bearing because I didn't realize the drum had worn through the bearing already.

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

snap in snap out

The repair was simple with my mechanic relative handling the tools. Total time about 25 minutes.

Previous repairs to the venerable machine with parts obtained freom Part Select and shipped to Germany: new drive motor and drum bearings.

I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.