GTMS570ED3WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from West Bloomfield, MI
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic handle in dryer broke off.
All I neede to do was buy the new part and snap it into place on the door. The hardest part was making the door usable while waiting for a new handle. The solution was good old duct tape. I just taped the old broken handle in place until the new one showed up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from pleasant grove, AL
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic Door Handle Cracked
Old handle popped out by pulling back and out. Inserted new handle by pushing in and forward. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Nora Springs, IA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom part of handle was loose
Opened up the package and took off existing door handle. The new one snapped right into place. This took all of 10 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from martinsville, IN
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer did not latch
easy to fix took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SONOMA, CA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
thumping noise with any kind of load
looked at video of dryer disassemble, replaced 4 bearing slides, reassembled. Dryer is perfect now , no noise. thank you for your parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bud from RCH CUCAMONGA, CA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken door handle
Snapped right into place , less than a minute, if that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from LOVELAND, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken lint filter.
Removed the broken lint filter and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MEMPHIS, TN
- Parts Used:
- WE18X25100, WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old dryer filter was cracked and bulb burnt out
Easy peasey! Just Removed/Replace screw-in type bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from SOUTHAMPTON, NJ
- Parts Used:
- WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
CONTINUOUS SQUEAKING WHEN RUNNING
Open Door /remove 2 screws in top of door opening (this releases the top panel) /Lift top panel off of dryer (it is tucked under control panel) Remove the white plastic "arch" (front drum bearing) on top of door panel / Install new drum bearing and 4 each of the "slides" on the bearing/ There are two on each side of the "front drum bearing"/ Reverse the disassembly process to finish/ . You'll need a standard flat tip screw driver and a Phillips heads crewdriver to do all work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from COMSTOCK PARK, MI
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squealing as drum rotated
Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leroy from MERIDIAN, ID
- Parts Used:
- WE09X27634, WE03X37317, WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No problems
Did repair as per the video except I did not disconnect wires, just swung front panel around. Only complaint...discovered parts were much more expensive than other sites.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Enterprise, AL
- Parts Used:
- WE1M462
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
With the help of doityourself guy on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from NEW PRT RCHY, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Poughkeepsie, NY
- Parts Used:
- WE3M26, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer started to thump and scrape
First and most important - safety. Either unplug the dryer or shut off the circuit breaker. Remove the two screws to the top cover. To locate these screws just open the door as they are located at the top of the door opening. Remove screws and lift up the top cover and carefully pull towards you. Place to the side away from the work area. This now will expose two screws within the side panels holding the front door and front housing. Remove the two screws, lift up and out to remove front housing assemble. Be careful when you remove as the wiring to the light fixture is included. Just remove cover and place side ways close to the dryer.
Remove the bulb then remove the white plastic drum bearing (snaps out or in when replacing with a flat screwdriver).
Prior to installing the new drum bearing install the four white slide strips on top of the drum bearing. Review the old parts for comparison. These actually act as the bushings between the drum bearing and the clothes drum. Please keep in mind the slides do not come with the drum bearing when ordering. You must order seperately. Once the new assemble is snapped into the metal front cover/door now you can re-assemble. While you have the drum exposed it's a good time to check the belt for wear. Sometimes a worn or ripped belt can be the same symptom of the thumpimg sound. For the assemble just reverse all the earlier steps. Plug cord back in or turn on the circuit breaker and run the dryer. You should be good to go for more years of service.
Remove the bulb then remove the white plastic drum bearing (snaps out or in when replacing with a flat screwdriver).
Prior to installing the new drum bearing install the four white slide strips on top of the drum bearing. Review the old parts for comparison. These actually act as the bushings between the drum bearing and the clothes drum. Please keep in mind the slides do not come with the drum bearing when ordering. You must order seperately. Once the new assemble is snapped into the metal front cover/door now you can re-assemble. While you have the drum exposed it's a good time to check the belt for wear. Sometimes a worn or ripped belt can be the same symptom of the thumpimg sound. For the assemble just reverse all the earlier steps. Plug cord back in or turn on the circuit breaker and run the dryer. You should be good to go for more years of service.
Was this instruction helpful to you?
Thank you for voting!