DDC5200MDL General Electric Dryer - Instructions

The info from your web site was helpful. I had never taken a dryer apart and the instructions made the job easy. Used socket set to remove the back panel and top control panel. Then used a phillip's screwdriver to remove the two screws that hold the top of the dryer; these screws are accessed by opening the door to the dryer. To remove the front of the dryer remove to the two screws that are located at the top upper corners where front panel meet the side panel. Once these two screws are removed, remove the belt from around the drum and lift the drum out. The drum bearing is located on the back of the drum; remove the remnants of the old bearing and replace it with the new one. Retrace your steps to put the dryer back together. To get the belt back on track you will have to remove the lower back panel to access the belt drive and tension pulley. It is not difficult. God bless you.

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

the replacement part was easy to replace but remembering how the belt went back on took alittle more time..

I was unsure of how to disassemble the machine to reach the belt, but a YouTube video gave me confidence. Thanks to Partselect.com, the great customer service, and fast delivery. I had my dryer up and running really fast! The process was really not difficult at all and it gave me a chance to vacuum out years of trapped lint. I am so happy to have saved hundreds of dollars, not having to buy a new dryer.I would urge other folks to tackle these relatively simple repairs, the right parts are a phone call away. Frank

I noticed the original blower wheel was worn, the hole for the motor shaft was reamed out and the blower was not spinning with the motor. Air was not being circulated so the clothes were not drying well. Replacing the wheel was relatively easy. I did see other people commenting on the difficulty of getting the drive belt re installed properly. I noticed a small "lip" bent into the motor frame, and found the arm for the belt tensioner would fit into this lip and it held it out of the way while I reinstalled the drum and reouted the belt onto the motor pulley. Once the belt was in place, I gently let the tensioner out of its holding position and everything went back into place nicely.

I watched video supplied from parts select, only took about 30 minutes, hardest part was putting belt back on, couldn't fit hands in easily, but once I did it, dryer is like new, can't hear a thing.

found a bad heating element upon dissassembly had to remove drum to get to bearing.removed heating element coil and housing to replace bearing assembly.reassemble unit and test

Watched the video on YouTube and everything went great!

Removed drum, replaced bearing. Installed new belt. Reinstalled drum. No problem

Remove the Torx screws along the front top edge and flipped the top back. Removed two screws at the top inside holding the front panel on. Loosened two screws at the front bottom and took the front panel off. Pulled the drum out the front. I gave everything a good vacuuming with a shop vac and a long handle brush. Then went around back, removed the access panel, removed the rear drum bearing plate and installed the new one. Removed the rear bearing from the back of the drum and installed the new one (You have to work from both sides of the drum which makes it a little tricky.I used a couple of wire ties to hold everything in place while I lined everything up. Screws or punches would work too). The front drum slides are held in by 2 screws each and you could replace them without removing the drum. They need to be lubed with the lubricant supplied. I put the drum partially in then looped the belt over the narrow back part of the drum, around the motor pulley and idler pulley. Put the drum all the way in and the belt onto the drum by rotating it by hand. The belt ribs go against the drum. Installing the belt was the a little tricky but not impossible. It could be easier if you loosen the left side panel to give you some room to reach in but I was able to do it without doing that. Threw the front and top back on and was done. Total time was about 1.5 hours a lot of which was spent getting the dryer in and out of the little cubby hole it lives it.

Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.

I unplugged the dryer and moved it into a open spot on the floor.I then opened the door so I could release the top panel,and tilted it back.This allows the removal of the front of the unit. Folled the instuction for removing the drum and got it out. Cleaned up the area and removed the screws that held the drum to the bearing, and pulled the drum out. The instructions for removing the plate and the bearing where o.k., and the tips given for reassembly were helpful, but would have been easier to see if the were a seperate line. The parts fit GREAT, and this 1989 dryer is ready for a few more years.A good price on the parts and a quick ship.I will shop here again!

sort of followed instructions, would have beenhelpfull if they told me I HAD TO REACH INTO THE MOUTH OF A SABRE TOOTHED TIGER to install the new belt.

I didn't know what was wrong at first, only that the dryer would not start. I bought it used so had no fear of taking it apart to diagnose. Found the broken belt inside, ordered a replacement, installed the new belt, then crossed my fingers. Was pleasantly surprised that was all that was wrong and that for less than $20, including shipping, a few hours of my time, and a little help from YouTube videos the dryer is working again!

The same procedures as posted in the video, but as applied to the model. Belt had broken. Bearing and front supports were worn, but the cause of the noise was a worn tensioner pulley bearing/arm, causing damage to the belt until breakage. Save the time and effort of a second repair and purchase a tensioner arm/pulley anytime the belt breaks as this is likely the cause of the original breakage. The hardest part on this older GE was getting under the drum to engage the tensioner and belt to the motor, as clearances we very tight. Review the diagrams, watch the video, and enjoy a quiet and well running machine for your efforts. PartsSelect is the only place to shop for appliance parts, my hat's off to excellent service, fair pricing and fast shipment. Thanks PartSelect!