CDM2000TW419 General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michell from Bellefontaine, OH
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Loud Sqeaking noise
the replacement part was easy to replace but remembering how the belt went back on took alittle more time..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Mansfield, MA
- Parts Used:
- WE11M23
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dryer was not heating up
Had to remove the drum to get at the heater element also had to swop the sensers to the new element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elbert from LAWTEY, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Squeeky
Watched the video on YouTube and everything went great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hopatcong, NJ
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud screeching noise
I watched video supplied from parts select, only took about 30 minutes, hardest part was putting belt back on, couldn't fit hands in easily, but once I did it, dryer is like new, can't hear a thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Redondo Beach, CA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not stay closed
inserted the latch into the opening in the front face of the dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Port Charlotte, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
It was only a matter of putting a new knob in place of the broken one. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bakersfield, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dryer Start knob broken inside of stem.
Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Oregon, OH
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Loud Squeek When Started until warmed-up
Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Sidney, NY
- Parts Used:
- WE11M23
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
heating element went bad
Took the dryer apart in an adjacent unused bedroom. Saw that the element was bad. Ordered new part from Part Select and installed when it arrived. The whole situation went as smooth as could be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis G from Naples, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Holes were not threaded on rear bearing kit
Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nate from Affton, MO
- Parts Used:
- WE11M23
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Dryer runs but does not heat
My dryer would run but not heat and the timer would not advance. PartSelect helped me determine that the heating element needed to be replaced. I have very little experience with appliance repair. I found this to be challenging but well worth it.
Was this instruction helpful to you?
Thank you for voting!