61140419 General Electric Dryer - Instructions

replaced rear drum bearing kit Still makes the same noise

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

Snaped the new handle back on...no tools needed,
just fit the plastic groves of the handle into the holes on the dryer door. Very simple!

just put new one on. no tools needed fits in holes already there. handle just snaps on,

I just snapped the door handle on the dryer in less than a minute. I am completely satified. Did I mention I received my part in one day. I ordered online before 3pm and received it the next day before 11am. Very impressed. Thanks PartSelect!!!

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

r/r parts unit runs great

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!

First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).

Unplugged machine and turned off the gas. Removed top panel,4 screws along inside top edge of door opening. Used a wooden shim to pry the drum away from the surrounding "lip with felt padding. Slipped belt through.the trick is getting the belto around the entire drum. First I got it over the top of the drum, and fed it around the bottom by turning the drum and pushing the belt through the opening made by the shim between the bottom of drum and the lip with felt. It was kind of like feeding a bicycle chain onto a sprocket as you turn the wheel..
Removed back panel and vent hose, removed old belt laying on floor of machine, fed the belt onto the motor pulley and the tension pulley. Tension pulley presses on top side of belt. Belt should be in same position on drum as old belt, you can see a friction mark all around the drum from the old belt.
Replaced panels and vent hose. Put felt padding back into place wherever it slipped out. Very important because if you don't it scrapes the drum when turned on and makes a loud sound.
Dryer works perfectly again.

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

This repair was SO easy, it took less than 5 minutes. All I had to do is snap the door handle into the slots and it was finished. "Piece of Cake"!