GDL3040R*429 General Electric Dryer - Instructions

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

- Removed two screws at top left and right of door.
- Removed top dryer panel
- Removed two screws holding front panel in place
- Noticed drum slide was missing because front drum bearing was worn away and slide had fallen off.
- Went ahead and removed drum to replace rear drum bearing (probably not needed; should have disassembled it first to discover this). Would have been better to pull drum first (loosen idler pulley and release belt, pull drum straight out) instead of attempting to unscrew bearing. Be sure to note how the idler pulley is set.
- vacuumed tons of lint up
- Replaced bearing (needed a second person for this; drum too big to reach around. be sure to pre-thread the bearing)
- Ordered front drum bearing, waiting to repair it now, should be good after this.

Removed the top, four screws under the front inside the open door. Then the removed the front, two screws inside at top by drum and two screws on bottom. Then pulled out the drum, from there I was able to get to the bearing that was bad. Mine was a older model than the instructions showed that came with my repair parts but it was colse enough to get the job done. Your website is AWESOME!!! The entire experience was wonderful and made my repair as painless as possible. I have already recomended it to my friends, keep up the great work.

Had a repair shop quote 230 for repair . Spent 66 on parts and did the repair in 45 minutes using the instructions from folks on this site . Very happy with results thanks

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

unpluged the dryer removed the rear panel pry off control knob removed two scews for timer moved the two wires from old timer and put on new timer put back in with the two screws put knob on install rear panel plug in dryer tested it to make sure it worked properly i am done.

Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!

I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa

I took out a whooping four (4) screws, two that held down the top to the front panel then two screws that attached the side panels (at the top) to the front panel, raised the drum from the inside, leaned the front panel foreword, popped out the old slide (there was only one left), installed the four new slides & put it back together. That's pretty much all there was to it, vary simple.

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier